Справочник Пользователя для Nady Systems CX-222SW
1.
POWER SWITCH
To turn the unit ON or OFF, press the upper or lower
portion of this button. The internal power LED illuminates
when the unit is turned “ON”. (Caution: Always turn the
Crossover ON before the amplifier, and turn it OFF after
the amplifier or transients harmful to the speakers
may result.)
To turn the unit ON or OFF, press the upper or lower
portion of this button. The internal power LED illuminates
when the unit is turned “ON”. (Caution: Always turn the
Crossover ON before the amplifier, and turn it OFF after
the amplifier or transients harmful to the speakers
may result.)
2.
CROSSOVER FREQUENCY CONTROLS:
These select the crossover frequencies of the LOW and
HIGH ways. They’re a low cut for the HIGH and a high
cut for the LOW. You can select the frequencies
between 250 Hz and 6 Hz.
These select the crossover frequencies of the LOW and
HIGH ways. They’re a low cut for the HIGH and a high
cut for the LOW. You can select the frequencies
between 250 Hz and 6 Hz.
3.
L/H OUTPUT LEVEL CONTROLS:
These are used to adjust the output level of each way: LOW and HIGH .
These are used to adjust the output level of each way: LOW and HIGH .
4.
LOW CUT BUTTONS FOR LOW WAY:
These insert low cut filters in the LOW way of each stereo channel with a 12dB/Octave, 30 Hz HPF
to minimize problems from subsonic frequencies in the signal, to suppress hum, and to prevent low
frequency speaker resonance.
These insert low cut filters in the LOW way of each stereo channel with a 12dB/Octave, 30 Hz HPF
to minimize problems from subsonic frequencies in the signal, to suppress hum, and to prevent low
frequency speaker resonance.
5.
PHASE BUTTONS:
These allow switching the polarity to invert the signal phase on the HIGH ways. This is done after
the output levels are set to correct audible phase problems.
Caution: Before pressing the PHASE BUTTON, always lower the outputs of your power amplifiers
to avoid possible speaker damage.
These allow switching the polarity to invert the signal phase on the HIGH ways. This is done after
the output levels are set to correct audible phase problems.
Caution: Before pressing the PHASE BUTTON, always lower the outputs of your power amplifiers
to avoid possible speaker damage.
6.
SUB CROSSOVER FREQUENCY CONTROL:
This selects the crossover frequency of the SUB WOOFER way. You can select the frequency
between 50 Hz to 250 Hz.
This selects the crossover frequency of the SUB WOOFER way. You can select the frequency
between 50 Hz to 250 Hz.
7.
SUBWOOFER OUTPUT LEVEL CONTROL:
This is used to adjust the SUB WOOFER output level.
This is used to adjust the SUB WOOFER output level.
8.
SUBWOOFER LOW CUT BUTTON:
This inserts a low cut filter in the SUBWOOFER way with a 12dB/Octave, 30 Hz HPF to minimize
problems from subsonic frequencies in the signal, to suppress hum, and to prevent low frequency
subwoofer speaker resonance.
This inserts a low cut filter in the SUBWOOFER way with a 12dB/Octave, 30 Hz HPF to minimize
problems from subsonic frequencies in the signal, to suppress hum, and to prevent low frequency
subwoofer speaker resonance.
CONTROLS AND CONNECTIONS
FRONT PANEL
2
3
6
2
4
5
1
5
7
8
4
4
PLEASE READ THIS MANUAL
BEFORE OPERATING THIS UNIT
Caution : To prevent malfunctioning
and/or possible equipment damage:
Before plugging the unit into the power
source: (1) the voltage selector switch
should be set for the correct voltage for
your area (115V or 230V) and (2) all
equipment connected to the crossover
outputs should be turned off or all the
inputs turned down.
3