Справочник Пользователя для Mitsubishi Electronics FR-V500
31
Names and functions of the opera-
tion panel
3.3.7
Copy mode
By using the operation panel (FR-DU04
-1
), the parameter values can be copied to another inverter (only the FR-
V500 series).
1)
1)
Operation procedure
After reading the parameter values from the copy source inverter, connect the operation panel to the copy des-
tination inverter, and write the parameter values.
After writing the parameter values to the copy destination inverter, always reset the inverter, e.g. switch power
off once, before starting operation.
After reading the parameter values from the copy source inverter, connect the operation panel to the copy des-
tination inverter, and write the parameter values.
After writing the parameter values to the copy destination inverter, always reset the inverter, e.g. switch power
off once, before starting operation.
Reference:
It is recommended to perform parameter read after completion of parameter setting. (When
performing auto tuning, it is recommended to perform read after completion of auto tuning.) When the
inverter has been changed, performing parameter write from the operation panel fitted to a new
inverter completes parameter setup.
performing auto tuning, it is recommended to perform read after completion of auto tuning.) When the
inverter has been changed, performing parameter write from the operation panel fitted to a new
inverter completes parameter setup.
CAUTION
1. While the copy function is being activated, the monitor display flickers. The display returns to the lit-
up state on completion of the copy function.
2. If a read error occurs during parameter read, "read error (E.rE1)" is displayed.
3. If a write error occurs during parameter write, "write error (E.rE2)" is displayed.
4. If a data discrepancy occurs during parameter verify, the corresponding parameter number and "ver-
3. If a write error occurs during parameter write, "write error (E.rE2)" is displayed.
4. If a data discrepancy occurs during parameter verify, the corresponding parameter number and "ver-
ify error (E.rE3)" are displayed alternately. If the directly preset speed or jog speed setting differs,
"verify error (E.rE3)" flickers. Press
to ignore this display and continue verify.
5. When the copy destination inverter is not the FR-V500, "model error (E.rE4)" is displayed.
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
V
REV
FWD
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
V
REV
FWD
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
REV
FWD
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
REV
FWD
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
REV
FWD
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
REV
FWD
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
V
REV
FWD
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
V
REV
FWD
FR-DU04
-1
CONTROL PANEL
Hz/r
MON
EXT
PU
A
V
V
REV
FWD
SET
SET
SET
(Caution 1)
SET
Connect to copy destination inverter.
Press for
1.5s
1.5s
After writing the parameter values,
always reset the inverter prior to
the start of operation.
always reset the inverter prior to
the start of operation.
Parameter setting mode
Parameter read
Parameter write
Parameter verify
Press for
1.5s
1.5s
Press for
1.5s
1.5s
(Caution 1)
(Caution 1)
SET