Справочник Пользователя для Liebherr 7085638-01

u

Align  the  appliance  so  that  it

stands firmly and on a level by

applying  the  accompanying

spanner  to  the  adjustable-

height  feet  (A)  and  using  a

spirit level.

u

Then support the door: Extend

the adjustable foot at the turn

hinge  (B)  until  it  rests  on  the

floor  and  then  make  a  further

90° turn.

When a Side-by-Side appliance (S…) is fitted together with

a second appliance (as a SBS combination):

u

Proceed  according  to  the  Side-by-Side  combined  fridge-

freezer installation instructions. (Accessories bag of the SBS

freezer/appliance with freezer compartment)

u

Clean the appliance (see 6.2) .

If  the  appliance  is  installed  in  a  very  damp  environment,

condensate may form on the outside of the appliance.

u

Always see to good ventilation at the installation site.

You can change over the door hinges if necessary.

Risk  of  damage  to  side-by-side  appliances  due  to  condensa-

tion!

When  a  side-by-side  appliance  (S…)  is  fitted  together  with  a

second  appliance  (as  a  SBS  combination),  the  door  hinges

must remain as delivered.

u

Do not change over the door hinges.

Ensure that the following tools are to hand:

q

Torx® 25

q

Torx® 15

q

Screwdriver

q

Battery-powered screwdriver, if necessary

q

Second person for fitting work, if needed

u

Remove any food from the door racks before removing the

door, so that no food falls out.

Fig. 4 

u

Close the door.

u

Pull off the cover

 Fig. 4 (10)

 forwards and upwards.

u

Lift off the cover

 Fig. 4 (11)

.

Risk of injury if the door tips!

u

Take good hold of the door.

u

Set down the door carefully.

u

Unscrew  the  upper  turn  hinge

  Fig.  4  (12)

(2x  Torx®  25)

Fig. 4 (13)

 and lift it off.

u

Lift off the door and set it aside.

Fig. 5 

u

Lift  out  the  bearing  pin

  Fig.  5  (22)

  together  with  washer

Fig. 5 (23)

 and adjustable-height foot

 Fig. 5 (24)

.

u

Lift off the stopper

 Fig. 5 (21)

.

u

Unscrew

 Fig. 5 (26)

 the turn hinge

 Fig. 5 (25)

.

u

Unscrew

 Fig. 5 (29)

 the bearing element

 Fig. 5 (28)

 , transfer

it to the opposite location hole of the turn hinge and screw it

firmly into place.

u

Carefully lift off the cover on the handle side

 Fig. 5 (27)

 and

transfer it to the opposite side.

u

Screw the turn hinge

 Fig. 5 (25)

 firmly into place on the new

hinge  side,  possibly  using  a  cordless  screwdriver  (with

4 Nm).

u

Re-insert the stopper

 Fig. 5 (21)

 into the other hole.

u

Re-insert  the  bearing  pin

  Fig.  5  (22)

  together  with  the

washer and adjustable-height foot. In so doing, pay attention

that the locating lug points backwards

u

Transfer the spring clamp

Fig.  6  (31)

:  Depress  the

latch  nose  and  pull  the

spring clamp off over it.

u

Slide  the  spring  clamp

into  place  on  the  new

hinge  side  until  it  clicks

into place.

Fig. 6