Листовка для Cirkuit Planet GT-702
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
- 9 -
- 10 -
3. CHECKLIST
Your GT-70X carton should contain the following items:
● The Gigabit Ethernet Converter.
● AC-DC Power Adapter (Output: 5VDC, 2A max.).
● This user’s manual.
If any item is missing or damaged, please consult the
dealer from whom you purchased your Gigabit Ethernet
Converter.
dealer from whom you purchased your Gigabit Ethernet
Converter.
Note
GT-705A is with one vacant SFP module slot.
The mini GBIC SFP module is not bundled
with in the package
The mini GBIC SFP module is not bundled
with in the package
4. PRODUCT OUTLOOK
Right View (GT-70X)
Left: Fiber-optic connector, Right: TP connector.
Three LED indicators per TP, fiber port.
Three LED indicators per TP, fiber port.
Rear View (GT-70X)
Off
A-N bypass
On
5V DC
+
One DC jack for DC power input and DIP switch to disable/
enable Auto by pass function.
enable Auto by pass function.
Note
Please note that if converter is connect with
switch which is Auto negotiation supported,
please enable the A-N bypass function. If both
devices are conveters then please disable the
A-N bypass function.
switch which is Auto negotiation supported,
please enable the A-N bypass function. If both
devices are conveters then please disable the
A-N bypass function.
5. LED INDICATION
LED
Color
Description
Fiber / ACT
Green
Lit: when the fiber port run in fix
1000Mbps and packet is traveling.
1000Mbps and packet is traveling.
TP/ ACT
Green
Lit: when the packet is traveling.
Fiber / LNK
Green
Lit: when fiber connection is good.
TP / LNK
Green
Lit: when TP connection is good.
FDX
Green
Lit: when the TP port runs in
1000Mbps Full duplex.
1000Mbps Full duplex.
PWR
Green
Lit: when +5VDC power detected.
6. INSTALLING THE CONVERTER
Stand-alone Installation:
To install a GT-70X stand-alone, on a desktop or shelf,
simple complete to following steps:
simple complete to following steps:
● Turn off the power of the device/station in a network to
which the GT-70X will be attached.
● Ensure that there is no activity in the network.
● Attach fiber cable from the GT-70X to the fiber network.
TX, RX must be paired at both ends.
● Connect the 5VDC power adapter to the GT-70X and
verify that the Power LED lights up.
● Turn on the power of the device/station; the PWR LEDs
should light when all cables are attached.
Note
To prevent from optic acceptor malfunction,
check the both wires / transmitter before
power on the converter.
check the both wires / transmitter before
power on the converter.
GT-705A
● Connect the fiber cable. Attach the duplex LC connector
on the network cable into the SFP transceiver.
● Attach fiber cable from the GT-705A to the fiber network.
TX, RX must be paired at both ends.
● Connect the 5VDC power adapter to the GT-705A and
verify that the Power LED lights up.
● Turn on the power of the device/station; the PWR LEDs
should light when all cables are attached.
Note
It recommends using PLANET MGB-SX /
MGB-LX series 1000Base-SX/LX SFP on the
converter. If you insert a SFP transceiver
that is not supported, the converter will not
recognize it.
MGB-LX series 1000Base-SX/LX SFP on the
converter. If you insert a SFP transceiver
that is not supported, the converter will not
recognize it.
7. DUPLEX MODE SUPPORT
The GT-70X is one-channel media conversion between
1000Base-T and 1000Base-SX/LX/LX WDM. 1000Base-T
port can work under Auto-negotiation and fixed 1000Mbps
full duplex mode. 1000Base-SX/LX/LX WDM fiber port only
work at fixed 1000Mbps full duplex mode.
1000Base-T and 1000Base-SX/LX/LX WDM. 1000Base-T
port can work under Auto-negotiation and fixed 1000Mbps
full duplex mode. 1000Base-SX/LX/LX WDM fiber port only
work at fixed 1000Mbps full duplex mode.
Note
The fiber interface do not support Auto-
negotiation and can not work with 1000Base-
SX/LX interface that can not configure to fixed
1000Mbps full duplex.
negotiation and can not work with 1000Base-
SX/LX interface that can not configure to fixed
1000Mbps full duplex.
8. POWER INFORMATION
The power jack of GT-70X is with 2.5mm in the central post
and required +5VDC power input. It will conform to the
bundled AC-DC adapter and Planet’s Media Chassis. Should
you have the problem to make the power connection,
please contact your local sales representative.
and required +5VDC power input. It will conform to the
bundled AC-DC adapter and Planet’s Media Chassis. Should
you have the problem to make the power connection,
please contact your local sales representative.
Please keep the AC-DC adapter as spare parts when your
GT-70X is installed to a Media Chassis.
GT-70X is installed to a Media Chassis.