Листовка для RCA RT2906

It's important to read this instruction prior to using your new product for the first time.

811-AV6291W111

Printed in China

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference 

to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, which can be determined 

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures:

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 

• 

connected.

Consult the dealer or an experienced radio / TV technician for help.

• 

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for 

compliance could void the user's authority to operate the equipment.

This class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment 

Regulations.
The Shock Hazard Marking and Associated Graphical Symbol is provided on the bottom panel of unit.

Refer to the identification / rating label located on the back panel of your product for its proper 

operating voltage.
IMPORTANT: The power cord can be unplugged to turn off the main power to the unit. It should also be 

easily accessible in an emergency.

Leave sufficient space around the appliance to allow adequate ventilation: 10cm on either side and 

• 

at the back, as well as 7cm above it are ideal. 

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

The AC power plug is polarized (one blade is wider 

than the other) and only fits into AC power outlets 

one  way.  If  the  plug  won’t  go  into  the  outlet 

completely, turn the plug over and try to insert it 

the other way.

If it still won’t fit, contact a qualified electrician to 

change the outlet, or use a different one. Do not 

attempt to bypass this safety feature.

To prevent electric shock, match wide blade of 

•

plug to wide slot, fully insert.

The apparatus shall not be exposed to dripping 

•

or  splashing  and  that  no  objects  filled  with 

liquids,  such  as  vases,  shall  be  placed  on 

apparatus.

The  mains  plug  is  used  as  disconnect  device. 

•

The  mains  plug  of  apparatus  should  not  be 

obstructed OR should be easily accessed during 

intended use. To be completely disconnect the 

power input, the mains plug of apparatus shall 

be disconnected from the mains. 

This  product  should  be  serviced  only  by  those 

specially  trained  in  appropriate  servicing 

techniques.  For  instructions  on  how  to  obtain 

service, refer to the warranty included in this user 

manual.

Make  sure  you  connect  all  your  other  electronic 

components  and  the  speakers  before  plugging 

your unit into the outlet. Plug the power cord in 

the  wall  outlet,  matching  the  wide  blade  of  the 

plug  with  the  wide  slot  in  the  outlet.  Be  sure  to 

insert the plug completely.

Product: Dolby Digital Audio / Video Receiver

Brand:     RCA

Electrical Consumption
Power Supply: 120V ~ 60Hz

This Home Theater has earned 

the ENERGY STAR.

Do not play your headset at a high volume. 

• 

Hearing experts warn against extended high-

volume play.

If you experience a ringing in your ears, reduce 

• 

volume or discontinue use.

You should use extreme caution or temporarily 

• 

discontinue  use  in  potentially  hazardous 

situations.

Even  if  your  headset  is  an  open-air  type 

• 

designed to let you hear outside sounds, don't 

turn up the volume so high that you are unable 

to hear what is around you.

Excessive sound pressure from earphones and 

• 

headphone can cause hearing loss.

THE LIGHTNING FLASH AND ARROWHEAD 

WITHIN  THE  TRIANGLE  IS  A  WARNING 

SIGN  ALERTING  YOU  OF  “DANGEROUS 

VOLTAGE” INSIDE THE PRODUCT.

THE  EXCLAMATION  POINT  WITHIN  THE  

TRIANGLE IS A WARNING SIGN ALERTING 

YOU  OF  IMPORTANT  INSTRUCTIONS 

ACCOMPANYING THE PRODUCT.

Please read and save for future reference.

Some of the following information may not apply 

to  your  particular  product;  however,  as  with 

any electronic product, precautions should be 

observed during handling and use.

Read these instructions.

• 

Keep these instructions.

• 

Heed all warnings.

• 

Follow all instructions.

• 

Do not use this apparatus near water.

• 

Clean only with a dry cloth.

• 

Do  not  block  any  ventilation  openings. 

• 

Install in accordance with the manufacturer’s 

instructions.

Do  not  install  near  any  heat  sources  such 

• 

as radiators, heat registers, stoves, or other 

apparatus (Including amplifiers) that produce 

heat.

Do  not  defeat  the  safety  purpose  of  the 

• 

polarized or grounding-type plug. A polarized 

plug has two blades with one wider than the 

other. A grounding type plug has two blades 

and a third grounding prong. The wide blade 

or the third prong is provided for your safety.  

If the provided plug does not fit into your wall 

outlet, consult an electrician for replacement of 

the obsolete outlet.

Protect the power cord from being walked on 

• 

or pinched particularly at plugs, convenience 

receptacles, and the point where they exit from 

the apparatus.

Only use attachments / accessories specified by 

• 

the manufacturer.

Use only with a cart, stand, tripod, bracket or 

• 

table specified by the manufacturer, or sold with 

the apparatus. When a cart is used, use caution 

when moving the cart / apparatus combination 

to avoid injury from tip-over.

Unplug this apparatus during lightning storms 

• 

or when unused for long periods of time.

Refer  all  ser vicing  to  qualified  ser vice 

• 

personnel.  Servicing  is  required  when  the 

apparatus has been damaged in any way, such 

as the power cord or plug is damaged, liquid 

has been spilled or objects have fallen into the 

apparatus, the apparatus has been exposed to 

rain or moisture, does not operate normally, or 

has been dropped.

Additional safety information
•  Apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such 

as vases, shall be placed on the apparatus.

•  Always leave sufficient space around the product

for ventilation. Do not place product in or on a bed, 

rug, in a bookcase or cabinet that may prevent air 

flow through vent openings.

•  Do not place lighted candles, cigarettes, cigars,

etc. on the product.

•  Connect power cord only to AC power source as

marked on the product.

•  Care should be taken so that objects do not fall

into the product.

•  Do not attempt to disassemble the cabinet. This

product does not contain customer serviceable 

components.

If  your  product  operates  on  batteries,  adhere  to 

the following precautions:

A. Any battery may leak electrolyte if mixed with a 

different battery type, inserted incorrectly, or if 

all batteries are not replaced at the same time.

B.  Any  battery  may  leak  electrolyte  or  explode  if 

disposed of in fire or an attempt is made to charge 

a battery not intended to be recharged.

C. Discard  leaky  batteries  immediately.  Leaking 

batteries can cause skin burns or other personal 

injury.  When  discarding  batteries,  be  sure  to 

dispose of them in a proper manner, according 

to your state / provincial and local regulations.

D. Battery shall not be exposed to excessive heat 

such as sunshine, fire or the like.

]

•  One main unit

•  One remote control with batteries

•  One pair of front speakers, one pair of rear speakers,

one center speaker and one subwoofer

•  One pig-tail antenna wire

•  One AM loop antenna

•  One coaxial digital cable

•  One pair of audio cable for analog connections

•  One English & one Spanish user manuals

•  One English & Spanish quick start guides

Provides spaces for sufficient ventilation as 

indicated: 

•  Do not connect to the AC power cords until all

connections are completed.

•  Do not use your set immediately after transferring

it from a cold place to a warm place: there is risk 

of condensation.

•  Do not expose your set to water and excessively

high temperatures.

•  After  having  disconnected  your  set,  clean  the

case with a soft cloth, or with a slightly damp 

leather chamois. Never using strong solvents.

•  Do not block ventilation holes in any component.

Arrange the components so that air can circulate 

freely.

•  Do not stack components directly on top of each

other.

•  Do not place the unit near other components

that generate heat such as heating vents.

•  Allow adequate ventilation when placing your

components in a stand.

•  Place an amplifier near the top shelf of the stand

so heated air rising from it will not affect other 

components. If you have a satellite receiver, you 

should place it on the top shelf.

AM loop antenna

3

3

1

1

2

4

Courtesy Dolby Laboratories

Front  speakers  carry  primarily  music  and  sound 

effects.
2. Center

In surround mode, the center speaker carries most 

of the dialog as well as music and effects.

It  should  be  set  between  the  left  and  right 

speakers.
3. Surround (Rear Speakers)

The  surround  speakers’  overall  sound  balance 

should be as close as possible to the front speakers. 

Proper  placement  is  vital  to  establish  an  evenly 

distributed sound field.
4. Subwoofer

A  subwoofer  is  designed  to  reproduce  powerful 

low  bass  effects  (explosions,  the  rumble  of 

spaceships, etc.).

Speakers placed less than two feet from the TV set 

must be magnetically shielded in order to prevent 

picture  distortion.  Center  speaker  provided  with 

this  unit  is  magnetically  shielded  to  protect  your 

TV set.

For  best  results,  follow  the  speaker  placement 

below.

Align the center speaker evenly with (A) or slightly 

behind  (B)  (the  left  and  right  speakers),  but  not 

ahead of them.

Place  the  left  and  right  speakers  to  form  a  45-

degree  angle  with  your  favorite  viewing  position 

to duplicate the soundtrack mixer’s perspective.

The  three  front  speakers  should  be  as  close  as 

possible  to  the  same  height.  This  often  requires 

placing  the  center  speaker  directly  on  top  (A)  or 

beneath (B) the TV set.

A

B

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

If possible, place surround speakers to either side of the listening area, not behind it.
Height

If  space  permits,  install  surround  speakers  2-3  feet  above  viewers.  This  helps  to  minimize  localization 

effects.
Aiming

Aim surround speakers straight across the room, not down at viewers, to help create a more open, spacious 

surround sound field.

If rear wall mounting is the only choice, aim the speakers at each other (A), towards the front (B) or towards 

the sidewalls (C, D).

Experiment with placement until sounds seem to surround you, rather than come from behind you.

Surround speakers can go on stands facing each other to approximate sidewall mounting (A), or to the 

sides or rear of the viewing area, aimed upwards; they can go right on the floor, or preferably, a few feet 

off the floor such as on end tables (B).

User Manual

- 1 -

- 9 -

- 8 -

- 7 -

- 10 -

- 5 -

- 4 -

- 3 -

- 6 -

- 2 -

CAUTION:  TO  REDUCE  THE  RISK  OF  ELECTRIC 

SHOCK,  DO  NOT  REMOVE  COVER  (OR  BACK). 

NO  USER  SERVICEABLE  PARTS  INSIDE.  REFER 

SERVICING TO QUALIFIED SERVICE PERSONNEL.

The  digital  audio  jacks  can  accept  Dolby  Digital  (Surround  Sound)  or  PCM  (Stereo)  signals  when 

compatible components are connected.

•  This  unit  provides  one  optical  and  one  coaxial  digital  input  jacks  for  the  connection  of  your 

components that have digital audio outputs.

•  To connect DVD player, Satellite receiver, Cable box, Blu-ray player or TV that has a digital audio

output, use a coaxial digital (included) or an optical digital cable (not included) to carry the audio 

signal and enjoy Dolby Digital sound quality.

•  A separate optical or coaxial cable is needed for each digital connection.

Notes: • If your TV has digital audio output, you can connect it to the corresponding digital

audio input of the system instead of using analog connection.
• Optical and coaxial cables carry only the audio portion of the signal.

User 

manual

1.     /   (TUNING buttons)
Tunes in to desired stations in AM/FM mode.

2.   ON/STANDBY
Turns on / off the unit. When the unit is turned on, the unit will go to the mode it was in before powered 

off.

Selects preset stations in AM/FM mode;

Selects item to be set in SETUP MENU.

4.   GAME jacks
Connects game consoles or other AV products that have AUX audio outputs.

5.   LINE IN
Connects portable audio devices or other AV products that have a LINE-OUT jack.

6.     /   (SURROUND buttons)
Selects among digital surround sound effects. (HALL, CHURCH, CLUB, STADIUM, STUDIO, STEREO, DOLBY 

PL EMULATION, DOLBY PL II MUSIC, DOLBY PL II MOVIE) depending on input signal.

Adjusts value in SETUP MENU.

7.  DVD, TV, SAT-CABLE, AM/FM, VCR, BD and GAME/LINE-IN (SOURCE buttons)
Selects sound source.

9.  MASTER VOLUME
Adjusts the volume.

10. SETUP
Enters or quits the SETUP menu. 

1

3

8

7

6

5

4

9

10

2

Blu-ray Disc Player 

Analog Audio 

Signals

Analog Audio 

Signals

Satellite Receiver or Cable Box

TV with HDMI Input

Optical Digital In (Audio)

Connect to optical digital output of Cable box, Satellite receiver, DVD, Blu-ray player, 

TV or other compatible devices using the Optical Fiber Cable (not included).

Coaxial Digital In (Audio)

Connect to coaxial digital output of DVD, Cable box, Satellite

receiver, TV or other compatible devices using the Coaxial Digital

Cable (included).

BD/DVD/SAT-CABLE/TV/GAME

BD/DVD/SAT-CABLE/TV/GAME

DVD player

Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each 

speaker  to  the  corresponding  color  terminal  at  the  back  of  the  unit.  Press  down  the  tab  to  open  the 

terminal and insert the wire. Release the tab to lock wire in the terminal.
When connecting the speakers, make sure the polarities (“+“ speaker wire to “+“ on the unit. For example, 
red wire to red terminal on the unit) of speaker wires and terminals match.
If the cords are reversed, the sound will be distorted. Do not let the speaker wires touch each other, it will 

damage the Home Theater’s amplifier.

Connect the AM and FM antennas to the AM and FM terminals on the system’s back panel.

They must be hooked up in order to receive clear reception. For FM reception, extend antenna to its full 

length. For AM reception, rotate the antenna horizontally to get better reception.

1.  Uncoil the antenna wire and locate the base end of the AM antenna.

2.  Press down on the antennas tab to open the  terminal.

3.  Insert the antenna wires into the terminal and release the tabs to secure the wires in place.

4.  Make sure the white wire on the AM loop antenna is inserted into the AM loop terminal and the other 

wire is inserted into the ground loop terminal.

Connect components, such as DVD players, Satellite receiver/Cable boxes, BD (Blu-ray Disc

TM

) players or TVs, 

capable of outputting Dolby Digital (Surround Sound) or standard PCM (Stereo) format digital signals.
Note: “Blu-ray Disc” is a trademark of Blu-ray Disc Association.

This class B digital apparatus complies

with Canadian ICES-003.

Cet appareil numérique de la classe B

est conforme à la norme NMB-003 du

Canada.

Left and right

front speakers

Left and right

rear speakers

Note:  This product will play audio from HDMI-connected products 

while also passing on the video signal to a HDMI-connected TV.

Quick start 

guide

Center 

Speaker

Right

Left

Rear Speakers

(Surround Sound)

Blue and Black

Grey and Black

Purple and Black

White and 

Black

Red and 

Black

Front Speakers

Green and Black

Use this jack on

the rear panel

to connect an

active subwoofer

other than the 

one supplied.

SUBWOOFER

AUDIO OUT

Subwoofer

Right

Left

Center speaker

Coaxial digital

cable

Audio cable for 

analog connections

Pig-tail

antenna wire

Remote

control with

batteries