Справочник Пользователя для Mitsubishi Electronics 737
52
6. NetCommand Control of an A/V Receiver (837 Series)
IMPORTANT
To hear audio sent from the TV to the A/V receiver,
you must have:
you must have:
Physically connected the TV to the A/V receiver
•
via the analog or digital audio output.
Assigned, if needed, the name AVR if using an
Assigned, if needed, the name AVR if using an
•
HDMI A/V receiver.
“
“
•
Learned” the IR codes for the A/V receiver
inputs.
Assigned the TV’s audio output to the correct
Assigned the TV’s audio output to the correct
•
input in the NetCommand Inputs > AVR menu.
Selected the A/V receiver as the audio source.
Selected the A/V receiver as the audio source.
•
Press MORE then 9 (AUDIO), then to show
the Speakers option, then to select the A/V
Receiver.
the Speakers option, then to select the A/V
Receiver.
Setting Up A/V Receiver Control
Power and Volume
Perform this setup to control the A/V receiver power
and volume with the TV’s remote control.
and volume with the TV’s remote control.
To perform this setup you need:
The remote controls for both the TV and the
•
A/V receiver.
An IR emitter cable available from Mitsubishi.
An IR emitter cable available from Mitsubishi.
•
Before You Begin
Connect your A/V receiver to the TV and any addi-
1.
tional devices. See “Setting Up TV Inputs,” page 10
and “TV Connections,” page 14.
Connect the IR emitter cable to the TV and position
and “TV Connections,” page 14.
Connect the IR emitter cable to the TV and position
2.
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 46.
Set the
receiver. See “IR Emitter Placement,” page 46.
Set the
3.
TV’s remote control to TV mode using the
side button.
Setup to Control A/V Receiver Power and Volume
Open the
1.
Inputs > AVR screen in one of two ways:
If using the
•
New Device Found screen for the
A/V receiver, highlight
NetCommand and press
ENTER to open the AVR screen.
If performing NetCommand setup at any time
If performing NetCommand setup at any time
•
after Auto Sensing:
Press
Press
MENU, highlight Inputs, and highlight AVR
to open the
AVR menu.
The first function highlighted in the
2.
AVR screen is
always
Power. Aim the TV’s remote control at the
TV and press
ENTER to begin learning for Power.
Inputs > AVR screen. Perform
NetCommand IR “learning” for A/V
receiver power and volume keys.
NetCommand IR “learning” for A/V
receiver power and volume keys.
When the
3.
Power text starts flashing, aim the A/V
receiver’s remote control at the TV and hold the
POWER or POWER ON key until a check mark appears
next to
POWER or POWER ON key until a check mark appears
next to
Power.
If the text stops flashing before the check mark
•
appears, repeat this step.
To remove the key from NetCommand control,
To remove the key from NetCommand control,
•
press the
CANCEL key while the key name is
highlighted.
Press the
4.
key on the
TV’s remote control to highlight
other keys in the list. Repeat steps 2 and 3 for each addi-
tional function you wish to control through NetCommand.
If the A/V receiver has a separate
tional function you wish to control through NetCommand.
If the A/V receiver has a separate
5.
POWER OFF key,
press on the
TV’s remote to highlight Power Off.
Repeat steps 2 and 3 to “learn” the
POWER OFF key.
If the device has no POWER OFF key, skip this step.
When finished “learning” the power and volume
When finished “learning” the power and volume
6.
keys, either
To watch TV, press
•
BACK .
To continue with NetCommand setup to control
•
switching of A/V receiver inputs, highlight
NEXT and press ENTER.
NEXT and press ENTER.