Справочник Пользователя для Philips LivingColors

EN Instruction for Use

Thank you for buying Philips LivingColors!

LivingColors has been especially designed to create your own ambiance

at home, through colour and light.

If using LivingColors for the first time, please read these instructions

carefully and save them for future reference. By following our guidelines,

you will enjoy the full functionality of Philips LivingColors.

Important:

-Carefully remove the parts from the packaging.

-Check whether all parts are available.

Getting started:

1. Open the battery compartment of the remote control by sliding

the button at the back. Insert 3 AAA batteries (+ and – as

indicated) (drawing a).

2. Place LivingColors at a selected location on a flat and stable surface.

Direct LivingColors towards the wall (the optimal distance is

50 cm), insert the connection plug into the lamp (drawing b), and

then plug it into the wall socket. LivingColors will show a short

introduction to the colour possibilities.

3. Switch on LivingColors by briefly pressing the "I" (on) on the on/off

button placed on the remote control (drawing c).

4. Create your own ambiance by:

-Touching the desired colour on the colour wheel. You can move

your finger over the colour wheel to refine the colour (drawing d)

-Changing the colour saturation (adding more white to the current

colour). Press on ( ) for a deep colour or on ( ) for a more

pastel colour (drawing e). Ultimately you will reach the white

colour.

-Dimming. Increase ( ) or decrease ( ) the light intensity via the

dimming buttons (drawing f).

5. Switch off LivingColors by pressing the "0" (off) button briefly.

LivingColors will remember your last colour setting for your next

usage (drawing c).

Do more with LivingColors:

1.Automatic colour-changing mode

Sweep your finger around the colour wheel (one full circle) and

briefly press on "I" ("On"); LivingColors will then turn into the

automatic colour-changing mode: the lamp will start changing

colours automatically.

You can adjust the speed with which colours change. Speed can

be adjusted clockwise, from fast (dark blue colour on the colour

wheel) to slow (purple) (drawing g). You can tap anywhere on the

colour wheel. While in the automatic colour changing mode, you

can also adjust the saturation and brightness of the colours.

To switch back to static colour mode, sweep around the

colour wheel again, then press "0". Alternatively, you can switch

LivingColors off "0" and on "I" again. (drawing c)

2.Linking LivingColors lamps

1. You can operate multiple LivingColors with one remote control.

The LivingColors lamps will then project the same colour (or

will change colours simultaneously). In order to link several

LivingColors to one remote control, bring the remote close to

the Philips logo on the top of the lamp and press on "I" ("On").

LivingColors will flash 3 times, and then quickly flash green. You can

release the button now. The linked lamps will turn to the last setting

of the remote control.

- Repeat this operation for each LivingColors lamp that you want to

link with the others.

- To use the LivingColors separately again, link it to another remote

control in the same way as described above.

2. It is also possible to control one LivingColors lamp with several

remote controls. In order to do so, first reset one of the remotes

by pressing and holding the "0" and the ( ) buttons simultaneously

for 5 seconds. Then hold two remote controls close to each other

and press the "I" button on both for 7 seconds. You can now link

the new remote control to the LivingColors in the same way as

described above.

- LivingColors that are linked to two (or more) remote controls can

be controlled by either remote control.

- To unlink a remote control from a LivingColors, hold the remote

control close to the LivingColors and press "0" for three seconds.

The LivingColors will flash 3 times. Hold the "0" button a little

longer and it will slowly fade to off. The remote control and the

LivingColors are now unlinked.

3.Compatibility with timers

You can use LivingColors with a timer (not included). When

switched on with a timer, the LivingColors will show your last

setting (static colour or automatic colour-changing mode)

Cleaning and maintenance:

Remove the plug from the wall socket.

To avoid scratching, the LivingColors lamp, remote control and

adapter should only be cleaned with a soft dry cloth.

Do not use cleaning agents.

Safety instructions:

Keep the plug and LivingColors away from liquids and humidity.

- LivingColors is for indoor use only. Do not use in wet locations, e.g.

bathrooms or outdoors.

- LivingColors is not a toy designed to be played with by children.

- Do not place on hot surfaces

- For safety reasons and under the terms of the warranty, the

LivingColors and plug must not be opened.

- Only use the adapter supplied: using a different adapter can damage

your LivingColors.

Environment:

If you need to discard the appliance, dispose of it in accordance with

instructions from the local authority. Remove the batteries when you

discard the remote control. Do not throw the batteries away with

normal household waste. They must be handed in at an official collection

point or at a Philips Dealer, both of which will dispose of the batteries in

an environmentally friendly way.

Problem

Possible cause

Solution

LivingColors is not providing light

The lamp is not plugged in

correctly

Check the connections of the cord to the lamp
Check that the plug is correctly placed in the wall socket

Remote control is not working

See the following section

LivingColors does not respond to

the remote control

Remote control is not working

Check the batteries in the remote control. The batteries should

be correctly placed (+ and -) and should be charged. If the

remote control is still not working, try replacing the batteries.

Remote control is not linked to

the lamp

Link the remote to the LivingColors lamp by following the

procedure under “2. Linking LivingColors lamps”

Heavy traffic on a wireless data

network (e.g. wireless router)

Move LivingColors away from the wireless access point
Make sure that all LivingColors connected to this remote are

on; otherwise they will not respond after this action.

Press simultaneously on “0” and ( ) for at least 5 seconds

to switch to another channel (all LivingColors will flash green

to confirm). You can repeat this procedure up to 3 times,

preferably from another position.

I cannot link multiple LivingColors

lamps

“I” button wasn’t pressed long

enough

Redo the procedure under “2. Linking LivingColors lamps”. If

it was linked successfully, the lamp will give 1 green flash; if the

linking was unsuccessful it will revert to its previous settings

immediately without flashing green.

The LivingColors lamps belong to

different versions

Check if the lamps you cannot link both have a “G2” sign on the

back of the remote control and at the bottom of the lamp itself.

If one of the lamps does not have it, it cannot be linked with

another lamp that does (but it can still be linked with other

lamps that do not have the G2 sign).

I cannot start the automatic colour

changing mode

The sweep movement was not

correct

If the colour changes to another (static) colour, but no colour

loop starts, then your sweep movement was not correct; please

try again

LivingColors is still not working to

the correct standards