Руководство Пользователя для Indesit KP9F11SRG

! Before placing your new appliance into operation please 

read these operating instructions carefully. It contains 

important information concerning the safe installation and 

operation of the appliance.

! Please keep these operating instructions for future 

reference. Make sure that the instructions are kept with the 

appliance if it is sold, given away or moved.

! The appliance must be installed by a qualified professional 

in accordance with the instructions provided.

! Any necessary adjustment or maintenance must be performed 

after the cooker has been disconnected from the electricity supply.

The cookers have the following technical specifications:

The appliance may only be installed in permanently-

ventilated rooms, according to current national legislation. 

The room in which the appliance is installed must be 

ventilated adequately in order to provide as much air as is 

needed by the normal gas combustion process (the flow of 

air must not be lower than 2 m

3

/h per kW of installed power).

The air inlets, protected by grilles, should have a duct 

with an inner cross section of at least 100 cm

2

 and should 

be positioned so that they are not liable to even partial 

obstruction (see figure A).

These inlets should be enlarged by 100% - with a minimum of 

200 cm

2

 - whenever the surface of the hob is not equipped with 

a flame failure safety device. When the flow of air is provided in 

an indirect manner from adjacent rooms (see figure B), provided 

that these are not communal parts of a building, areas with 

increased fire hazards or bedrooms, the inlets should be fitted 

with a ventilation duct leading outside as described above. 

Examples of 
ventilation holes 
for comburant air.

 

Enlarging the ventilation slot

between window and floor.

Adjacent

Room

Room to be

Vented

A     B

! After prolonged use of the appliance, it is advisable to open 

a window or increase the speed of any fans used. 

The  efficient  disposal  of  combustion  fumes  should  be 

guaranteed using a hood which is connected to a safe 

and efficient natural suction chimney, or using an electric 

fan which begins to operate automatically every time the 

appliance is switched on (see figure).

In a chimney stack or branched flue. 

(exclusively for cooking appliances)

Directly to 

the Outside

! The liquefied petroleum gases are heavier than air and 

collect  by  the  floor,  therefore  all  rooms  containing  LPG 

cylinders must have openings leading outside so that any 

leaked gas can escape easily. LPG cylinders, therefore, 

whether partially or completely full, must not be installed or 

stored in rooms or storage areas which are below ground 

level (cellars, etc.). Only the cylinder being used should 

be stored in the room; this should also be kept well away 

from sources of heat (ovens, chimneys, stoves) which may 

cause the temperature of the cylinder to rise above 50°C.

! The appliance may be installed alongside any cupboards 

whose height does not exceed that of the hob surface.

! Make sure that the wall in contact with the back of the appliance 

is made from a non-flammable, heat-resistant material (T 90°C).

To install the appliance correctly:

•  Place it in the kitchen, the dining room or the studio flat 

(not in the bathroom).

•  If the top of the hob is higher than the cupboards, the 

appliance must be installed at least 500 mm away from them.

•  If  the  cooker  is  installed 

underneath a wall cabinet, there 

must be a minimum distance of 420 

mm between this cabinet and the 

top of the hob.

This distance should be increased 

to 700 mm if the wall cabinets are 

flammable (see figure).

•  Do not position blinds behind the cooker or less than 200 

mm away from its sides.

•  Any  hoods  must  be  installed  in  accordance  with  the 

instructions listed in the relevant operating manual.

If it is necessary to level the 

appliance, screw the adjustable 

feet into the places provided on 

each corner of the base of the 

cooker (see figure).

Install a standardised plug corresponding to the load indicated 

on the appliance data plate (see Technical data table). 

The appliance must be directly connected to the mains using 

an omnipolar switch with a minimum contact opening of 3 

mm installed between the appliance and the mains.