Справочник Пользователя для Vulcan-Hart 1GR35M
— 10 —
GR SERIES GAS FRYERS
Quick-Disconnect for Units on Casters
For an appliance equipped with casters:
•
The installation shall be made with a
connector that complies with the Standard
for Connectors for Movable Gas
Appliances, ANSI Z21.69 or Connectors for
Moveable Gas Appliances, CAN/CGA-6.16,
and a quick-disconnect device that
complies with the Standard for Quick-
Disconnect Devices for Use with Gas Fuel,
ANSI Z21.41, or Quick Disconnect Devices
for Use with Gas Fuel, CANI-6.9.
connector that complies with the Standard
for Connectors for Movable Gas
Appliances, ANSI Z21.69 or Connectors for
Moveable Gas Appliances, CAN/CGA-6.16,
and a quick-disconnect device that
complies with the Standard for Quick-
Disconnect Devices for Use with Gas Fuel,
ANSI Z21.41, or Quick Disconnect Devices
for Use with Gas Fuel, CANI-6.9.
•
When installing a quick disconnect you
must also install a means for limiting the
movement of the fryer. This device will
prevent the gas line or the quick
disconnect from being strained. The
restraining device should be attached to
the cutout on the back panel. See
illustration for location.
must also install a means for limiting the
movement of the fryer. This device will
prevent the gas line or the quick
disconnect from being strained. The
restraining device should be attached to
the cutout on the back panel. See
illustration for location.
A Rear of Fryer
B Strain Relief Chain Connection
B Strain Relief Chain Connection
(Chain supplied by others)
•
In Australia, use only the caster supplied
by the manufacturer for the fryer device.
The fryer must be installed using a hose
assembly restraining device to limit the
movement of the appliance in accordance
with AS1869.
by the manufacturer for the fryer device.
The fryer must be installed using a hose
assembly restraining device to limit the
movement of the appliance in accordance
with AS1869.
•
The fryer must be installed with a
connector (not supplied by Vulcan)
complying with the above code(s).
connector (not supplied by Vulcan)
complying with the above code(s).
•
The fryer must be installed with restraining
means to guard against transmission of
strain to the connector. See illustration.
means to guard against transmission of
strain to the connector. See illustration.
•
The fryer must be installed with the
casters provided.
casters provided.
•
If the restraint is ever to be disconnected,
first turn the gas supply OFF.
first turn the gas supply OFF.
ELECTRICAL CONNECTION
Note: Only the
KleenScreen™
style fryer
requires an electrical connection.
WARNING: ELECTRICAL AND
GROUNDING CONNECTIONS
MUST COMPLY WITH THE
NATIONAL ELECTRICAL
CODE AND / OR OTHER
LOCAL CODES.
MUST COMPLY WITH THE
NATIONAL ELECTRICAL
CODE AND / OR OTHER
LOCAL CODES.
WARNING: APPLIANCES EQUIPPED WITH
ELECTRICAL SUPPLY
CORD(S) ARE PROVIDED
WITH A THREE-PRONG
GROUNDING PLUG, WHICH
MUST BE CONNECTED TO A
PROPERLY GROUNDED
RECEPTACLE.
IF THE RECEPTACLE IS NOT
THE PROPER GROUNDING
TYPE, CONTACT AN
ELECTRICIAN. DO NOT
REMOVE THE GROUNDING
PRONG FROM THE PLUG.
CORD(S) ARE PROVIDED
WITH A THREE-PRONG
GROUNDING PLUG, WHICH
MUST BE CONNECTED TO A
PROPERLY GROUNDED
RECEPTACLE.
IF THE RECEPTACLE IS NOT
THE PROPER GROUNDING
TYPE, CONTACT AN
ELECTRICIAN. DO NOT
REMOVE THE GROUNDING
PRONG FROM THE PLUG.
KleenScreen™ fryers are equipped with a 120-V,
60-Hz, 1-phase cord and plug.
60-Hz, 1-phase cord and plug.
Do not connect fryer to electrical supply until
after gas connections have been made.
after gas connections have been made.
LEVELING THE FRYER
Check the level of the fryer by placing a level
on top of the fryer after gas connections have
been made.
on top of the fryer after gas connections have
been made.
Ensure that the fryer is level front-to-back and
side-to-side in the final installed position.
side-to-side in the final installed position.
If using casters, lock the wheels after unit is level.