Справочник Пользователя для Ariens 911099
GB - 22
SPEED CONTROL BELL CRANK
The speed control bell crank holds the speed
control rod in position after a speed has been
set. The spring washers may become loose
with normal wear. If the speed control rod
does not stay firmly in position, adjust the
speed control bell crank. See Figure 17.
To adjust:
control rod in position after a speed has been
set. The spring washers may become loose
with normal wear. If the speed control rod
does not stay firmly in position, adjust the
speed control bell crank. See Figure 17.
To adjust:
1. Remove cover, fully compress the
helical spring lock washers with lock
nut and then back lock nut off, one
quarter turn.
nut and then back lock nut off, one
quarter turn.
2. If the speed control rod is still too
loose, tighten lock nut by small
increments until it holds its position.
Tightening the lock nut too much will
not allow the speed control rod to
move at all.
increments until it holds its position.
Tightening the lock nut too much will
not allow the speed control rod to
move at all.
3. Align notch in left hand side of cover
with bolt and secure with knob.
IMPORTANT: NEVER spray unit with high-
pressure water or store unit outdoors. Store
mower in a cool, dry, protected location.
pressure water or store unit outdoors. Store
mower in a cool, dry, protected location.
Cleaning
Clean unit thoroughly with mild soap and low
pressure water. Brush off dirt and debris from
all surfaces. Touch up all scratched surfaces
to prevent rust. Matching touch-up paint is
available from your Ariens Dealer. Do not use
abrasives, solvents, or harsh cleaners.
pressure water. Brush off dirt and debris from
all surfaces. Touch up all scratched surfaces
to prevent rust. Matching touch-up paint is
available from your Ariens Dealer. Do not use
abrasives, solvents, or harsh cleaners.
Inspection
Inspect mower and repair or replace worn or
damaged parts to avoid delays when
beginning use again.
damaged parts to avoid delays when
beginning use again.
Regularly check all hardware and keep
fasteners tight. Know unit is in safe working
condition.
fasteners tight. Know unit is in safe working
condition.
Grass Bag
Wash out grass bag and allow to dry before
storage. Grass bag may be stored in position
on mower.
storage. Grass bag may be stored in position
on mower.
Battery
Fully charge battery and store in a cool, dry
location. See Service and Adjustments.
location. See Service and Adjustments.
IMPORTANT: Do not allow battery to freeze.
Engine
Close fuel shutoff valve (911099, 101, 102).
When storing unit for extended periods of
time, remove all fuel from tank and carburetor
(run dry). Refer to engine manual.
When storing unit for extended periods of
time, remove all fuel from tank and carburetor
(run dry). Refer to engine manual.
1. Lock Nut
2. Helical Spring
2. Helical Spring
Lock Washers
3. Speed Control
Bell Crank
4. Swivel
5. Hair Pin
6. Speed Control
5. Hair Pin
6. Speed Control
Rod
1
2
3
4
5
6
Figure 17
OM1670
STORAGE
CAUTION: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
and understand the entire Safety
section before proceeding.
TROUBLESHOOTING
PROBLEM
PROBABLE CAUSE
CORRECTION
Engine will not
start
start
1. Fuel tank empty or low.
2. Fuel shutoff valve closed.
3. Spark plug wire loose or off.
4. Battery discharged (electric
3. Spark plug wire loose or off.
4. Battery discharged (electric
start models).
5. Throttle control not in proper
position.
6. Engine/Blade control cable
detached, broken, or not
adjusted properly.
adjusted properly.
1. Check fuel level. Fill tank if
necessary.
2. Open fuel shutoff valve.
3. Check connection.
4. Charge battery or replace if
3. Check connection.
4. Charge battery or replace if
necessary.
5. Adjust throttle to FAST
position.
6. Check cable. Adjust, repair
or replace as necessary.