Инструкции Пользователя для Hoover s3755

Скачать
Страница из 11
Problem:  Cleaner won’t run
Problem:  Cleaner suction low
Problem:  Agitator brush roll 
won’t run
Problem:  Nozzle won’t pick up
Possible cause
Possible solution
• Not “ON” at hand grip.
Push Power ON/Suction Control slide 
switch forward.
• Not firmly plugged in.
Plug unit in firmly.
• No voltage in wall plug.
Check fuse or breaker.
• Blown fuse or tripped breaker.
Replace fuse/reset breaker.
Possible cause
Possible solution
• Hose power cord not firmly 
plugged in.
Plug firmly into receptacle on 
cleaner base.
• Broken or worn belt.
Replace belt.
• Floor/carpet switch set to “FLOOR”.
Set floor/carpet switch to “CARPET”.
Possible cause
Possible solution
• Low cleaner suction.
See section “Cleaner suction low”.
• Blockage in nozzle connector.
Remove blockage
• Agitator brush roll not running.
See section “Agitator brush roll won’t 
run”
• Agitator brush roll brushes worn.
Replace brushes.
Possible cause
Possible solution
• Dirt cup full.
Empty dirt cup.
• Dirt cup filter dirty.
Clean the dirt cup filter with brush and
water, allow to dry and replace in 
cleaner.
• Obstruction in nozzle connector, 
hose or wand.
Remove obstruction.
• Exhaust filter dirty.
Clean filter with water, allow to dry and
replace in cleaner.
• Power set too low.
Increase power setting by pushing 
Suction Control slide switch forward.
• Hose not properly connected to 
cleaner
Ensure hose is properly connected.
4. If you have a
problem 
10
If a minor problem occurs, it usually can
be solved quite easily when the cause is
found by using the check list below. 
4-1
4-2
A
Clearing blockages
When the cleaner senses low suction or
pickup, the red Suction Control light will
come on. Low suction or pick up may be
due to a blockage in the system. Refer
to the following steps to check for block-
ages, continuing with each step until the
blockage is found:
1. Turn cleaner off and 
disconnect from
electrical outlet; then disconnect
power nozzle plug and wands from
hand grip.
2. Plug cleaner in, turn on, and check
hose end for suction. Remove any
obstructions.
3. Remove power nozzle from wands
and attach wands to hose. Check for
suction and remove any blockages.
4. Make sure power nozzle plug is dis-
connected from hand grip. 
Then check
for blockage in nozzle connector (A).
Push nozzle connector down to lowest
position. Look into nozzle connector and
remove any blockage. 
Service 
To obtain approved HOOVER service
and genuine HOOVER parts, locate the
nearest 
Hoover Factory Service Center
or Authorized Hoover Warranty
Service Dealer (Depot) 
by:
• checking the Yellow Pages under 
“Vacuum Cleaners - Household” OR-
• checking the list of Factory Service
Centers provided with this cleaner 
OR -
• checking the Service section of 
The Hoover Company online at 
www.hoover.com 
OR -
• calling 
1-800-944-9200 
for an auto-
mated referral of authorized service 
outlet locations (U.S. only).
Please do not send your cleaner to The
Hoover Company in North Canton for
service, this will only result in delay.
If further assistance is needed, contact
The Hoover Company Consumer
Response Center, North Canton, Ohio
44720, Phone: 330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8, Phone: 
1-800-263-6376.
Always identify your cleaner by the 
com-
plete 
model number when requesting
information or ordering parts. (The model
number appears on the bottom of the
cleaner.)