Руководство Пользователя для GE PSB42YGXSV
Consumer
S
uppor
t
Tr
oubleshooting
Tips
Operating
Instructions
Safety
Instructions
Installation
Instructions
14
Replacing the light bulbs.
Setting the controls to OFF does not remove power to the light circuit.
Refrigerator Compartment—Upper Light
Raise the grille panel, set the master
power switch to the O (off) position and
allow lamps to cool.
power switch to the O (off) position and
allow lamps to cool.
To remove the light shield, press on
the sides of the shield and pull down.
the sides of the shield and pull down.
Replace the bulbs with appliance bulbs
of the same or lower wattage. Replace
the shield by engaging the bottom tab
into the slot and applying light forward
pressure until the shield snaps in place.
of the same or lower wattage. Replace
the shield by engaging the bottom tab
into the slot and applying light forward
pressure until the shield snaps in place.
Set the master power switch to the I (on)
position and close the grille panel.
position and close the grille panel.
Refrigerator Compartment—Lower Light
This light is located above the top drawer.
Raise the grille panel, set the master
power switch to the O (off) position
and allow lamps to cool.
power switch to the O (off) position
and allow lamps to cool.
Remove items from the shelf above
the light shield. Remove the shelf.
the light shield. Remove the shelf.
Use both hands to grasp each end
of the light shield. Press in on the bottom
of the shield with your thumbs while
rotating the cover up and out.
of the light shield. Press in on the bottom
of the shield with your thumbs while
rotating the cover up and out.
Replace the bulb with an appliance bulb
of the same or lower wattage. Replace
the shield by engaging the bottom tab
into the slot and applying light forward
pressure until the shield snaps in place.
of the same or lower wattage. Replace
the shield by engaging the bottom tab
into the slot and applying light forward
pressure until the shield snaps in place.
Set the master power switch to the I (on)
position and close the grille panel.
position and close the grille panel.
Freezer Compartment
Raise the grille panel, set the master
power switch to the O (off) position and
allow lamps to cool.
power switch to the O (off) position and
allow lamps to cool.
Remove the items from the shelf just
below the light shield. Remove the shelf.
below the light shield. Remove the shelf.
To remove the light shield, press down
on the top of the shield and pull the tabs
out of the slots. Tilt the shield forward
and out.
on the top of the shield and pull the tabs
out of the slots. Tilt the shield forward
and out.
Replace the bulb with an appliance
bulb of the same or lower wattage,
and reinstall the light shield. Replace
the shield by engaging the bottom tab
into the slot and applying light forward
pressure until the shield snaps in place.
bulb of the same or lower wattage,
and reinstall the light shield. Replace
the shield by engaging the bottom tab
into the slot and applying light forward
pressure until the shield snaps in place.
Set the master power switch to the I (on)
position and close the grille panel.
position and close the grille panel.
Dispenser
Raise the grille panel, set the master
power switch to the O (off) position
and allow lamps to cool.
power switch to the O (off) position
and allow lamps to cool.
The bulb is located in the dispenser
under the control panel. Remove
the two screws from the light shield.
Slide the light shield toward the
dispenser to disengage the tabs, then
remove the light shield. Remove the light
bulb by turning it counterclockwise.
under the control panel. Remove
the two screws from the light shield.
Slide the light shield toward the
dispenser to disengage the tabs, then
remove the light shield. Remove the light
bulb by turning it counterclockwise.
Replace the bulb with a bulb
of the same size and wattage. Replace
the light shield by sliding the tabs into
the slots in the front of the dispenser.
Replace the two screws.
of the same size and wattage. Replace
the light shield by sliding the tabs into
the slots in the front of the dispenser.
Replace the two screws.
Set the master power switch to the I (on)
position and close the grille panel.
position and close the grille panel.
(appearance may vary)