Руководство Пользователя для Sony PMW-320K
Adjusting the Black Balance and the White Balance
52
Chap
ter
3
3
Ad
jus
tme
nt
jus
tme
nt
s
an
d Set
d Set
tings
1
Set the OUTPUT/DCC switch to CAM.
2
Push the AUTO W/B BAL switch to
BLACK and release the switch.
The message “Executing...” appears during
execution, and changes to “Done” when the
adjustment finishes. Adjustment values are
saved to memory automatically.
BLACK and release the switch.
The message “Executing...” appears during
execution, and changes to “Done” when the
adjustment finishes. Adjustment values are
saved to memory automatically.
Notes
• During the black balance adjustment, the iris is
automatically closed.
• During the black balance adjustment, the gain
selection circuit is automatically activated so you may
see flickering on the viewfinder screen, but this is not
a fault.
see flickering on the viewfinder screen, but this is not
a fault.
• Output from the i.LINK connector stops temporarily if
you execute black balance adjustment during i.LINK
output. Output from the connector resumes when black
balance adjustment finishes.
output. Output from the connector resumes when black
balance adjustment finishes.
If automatic black balance adjustment
cannot be made
cannot be made
If the black balance adjustment cannot be
completed normally, an error message will appear
for about three seconds on the viewfinder screen.
Possible messages are listed below.
completed normally, an error message will appear
for about three seconds on the viewfinder screen.
Possible messages are listed below.
If any of the above error messages is displayed,
retry the black balance adjustment.
If the error message occurs again, an internal
check is necessary.
retry the black balance adjustment.
If the error message occurs again, an internal
check is necessary.
For information about this internal check, contact
your vendor or a Sony service representative.
your vendor or a Sony service representative.
Note
If the lens cable is not firmly connected to the LENS
connector, it may not be possible to adjust the lens iris. If
this happens, the black balance will be incorrect.
connector, it may not be possible to adjust the lens iris. If
this happens, the black balance will be incorrect.
1
Set the switches and selectors as shown
below.
• GAIN switch: L (set to a gain value that is
below.
• GAIN switch: L (set to a gain value that is
as small as possible)
• OUTPUT/DCC switch: CAM
• WHITE BAL switch: A or B
• WHITE BAL switch: A or B
1)
1) Adjustment values are saved to memory B only
when OPERATION >White Setting >White
Switch<B> in the setup menu, is set to
[Memory].
Switch<B> in the setup menu, is set to
[Memory].
2
Set the FILTER selector to suit the
lighting conditions as follows.
lighting conditions as follows.
3
Place a white test card under the same
lighting conditions as for the subject to
be shot and zoom up to it.
Alternatively, any white object such as a
cloth or a wall can be used.
The absolute minimum white area is as
follows.
lighting conditions as for the subject to
be shot and zoom up to it.
Alternatively, any white object such as a
cloth or a wall can be used.
The absolute minimum white area is as
follows.
Note
Make sure there are not bright spots in the
rectangle.
rectangle.
4
Adjust the lens iris.
Manually adjusted lens: set the iris to an
Manually adjusted lens: set the iris to an
appropriate setting.
Lens with automatic iris: set the automatic/
manual switch on the lens to automatic.
5
Push the AUTO W/B BAL switch to
WHITE and then release the switch.
The message “Executing...” appears during
execution, and changes to “OK: (color
temperature of subject)” when the
adjustment finishes.
WHITE and then release the switch.
The message “Executing...” appears during
execution, and changes to “OK: (color
temperature of subject)” when the
adjustment finishes.
Error message Meaning
NG: Iris Not
Closed
Closed
The lens iris did not close;
adjustment was impossible.
adjustment was impossible.
NG: Timeout
Adjustment could not be
completed within the standard
number of attempts.
completed within the standard
number of attempts.
NG: Out of
Range
Range
The difference between the
reference value and the current
value is so great that it exceeds
the range. Adjustment was
impossible.
reference value and the current
value is so great that it exceeds
the range. Adjustment was
impossible.
Adjusting the White Balance
Rectangle centered on the screen. The
lengths of the sides are 70% of the length
and width of the screen.
lengths of the sides are 70% of the length
and width of the screen.