Технический Паспорт Продукта для Conairphone pr5007

Your PR5007 is also designed to
mount on a wall surface over a
modular wall jack. Connect the short
telephone line cord to the modular
jack located on the bottom of base.
Insert the other modular plug into the
wall jack, making sure it snaps firmly
in place. Position the wall mount slots
on the bottom of the base over the
two studs of the wall plate. Pull down
to lock in place (see Diagram E).

When your phone rings, pick up the handset and use like any
basic telephone. Hang up the handset to release the telephone
line when conversation is completed.

NOTE: Before dialing, make sure the TONE/PULSE switch is
correctly positioned for your type of service.
Pick up phone, wait for a dial tone, press the keys for the number
you want. Your PR5007 (pulse setting) uses electronic pulses to
simulate dialing action. You might hear pulsing for a second or
two after the last button has been pressed.
NOTE: Your PR5007 features a lighted keypad for dialing in a
darkened room.

Your PR5007 remembers the last number dialed. If the number
you dial is busy or not being answered, hang up. To automatically
redial the last number, press the REDIAL button.
NOTE: You can redial the same number as many times as needed.
However, once you dial another number, the previous number is
erased.

• Handset
• Base
• One 6 ft. Fully Modular Line Cord
• One 7 ft. Fully Modular Coil Cord
• Owner’s Manual/Warranty Information
• One 5 inch Fully Modular Line Cord

Your PR5007 will operate on all systems, true tone or rotary.
1. If your home is wired for rotary service, move the TONE/PULSE

switch to PULSE position.

2. If your home is wired for Tone service, move the switch to the

TONE position.

3. If you are unsure of the type of service you have, position

TONE/PULSE switch to TONE. If dialing cannot be done, set
to PULSE.

Insert coil cord into modular
jack located on side of housing.
Connect the other end into the
modular jack located on the
handset (see Diagram B).

With a modular telephone
system, connect the long
telephone line cord to the
modular jack located on the
bottom of the base. Insert the
other end of cord into a modular
wall jack. Make sure all plugs
snap fir mly in place (see
Diagram C).

With a four prong style jack,
simply use a plug in a modular
adapter (see Diagram D).

Your PR5007 features a harmonic dual tone ringer which can be
adjusted to a loud (High) or soft (Low) sound level. When you
don’t want to be disturbed, slide switch to the “Off” position. Now
you can still make outgoing calls without being disturbed by
incoming calls.

The Receiver Volume Control is located on the side of your
handset. This enables you to adjust the receiver volume on your
telephone handset from normal to high for a more comfortable
listening level.

Problem: No dial tone
• Check all modular plugs to be sure they have clicked into place.
• Are cords damaged in any way?
• Try another phone jack. If your PR5007 works on another jack,

there may be a problem with your wiring.

Problem: I hear my phone dialing, but I can not get past the dial
tone.
• Check the tone/pulse switch. If positioned in TONE mode,

switch to PULSE. You may have pulse dialing service.

Problem: Phone doesn’t ring.
• Is ringer switch set to the “OFF” position.
• How many extensions are connected to your line? If more

than five telephones are installed on the same line, you may
need to contact your local telephone company to determine
the maximum number of extensions for your calling area.

Problem: The sound volume is too low.
• Is another extension off hook? If so, hang up extension.

Diagram B

Diagram C

Diagram D

Diagram E

4

5

6