Руководство Пользователя для Toshiba 42XV545U
37
XV545U (E/F) Web 177.8:228.6
Chapter 5: Setting up your TV
3
Open the Terrestrial menu, highlight Channel
Program
Program
to bring up Start, and press T again to
begin channel programming.
The TV will automatically cycle through all the
channels, and store all active channels in the channel
memory. While the TV is cycling through the
channels, the message “Scanning channels, please
wait” appears (as shown above).
channels, and store all active channels in the channel
memory. While the TV is cycling through the
channels, the message “Scanning channels, please
wait” appears (as shown above).
4
To cancel channel programming, press O on the
remote control (or highlight Cancel in the on-screen
display and press T).
When channel programming is finished, press
remote control (or highlight Cancel in the on-screen
display and press T).
When channel programming is finished, press
< or , to view the programmed channels.
Manually adding and deleting channels
in the channel memory
in the channel memory
After automatically programming channels into the
channel memory, you can manually add or delete
individual channels.
channel memory, you can manually add or delete
individual channels.
To add or delete channels in the channel memory:
1
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
press T. A new set of Installation menu icons will
appear.
2
Open the Terrestrial menu, highlight Channel Add/
Delete
Delete
, and then press T.
To add a channel to the channel memory:
Highlight the unchecked box next to the channel number
you want to add, and then press T to check the box.
you want to add, and then press T to check the box.
To manually add digital subchannels on a
physical channel:
physical channel:
Use the Channel Numbers and the Dash (=) on the
remote control to enter the channel number (for
example, 56–1).
If the channel is found, the number will be added to the
list and the box will be checked.
If the channel is not found, a message will appear.
remote control to enter the channel number (for
example, 56–1).
If the channel is found, the number will be added to the
list and the box will be checked.
If the channel is not found, a message will appear.
To remove a channel from the channel memory:
Highlight the checked box next to the channel number
you want to remove, and then press T to uncheck the
box.
you want to remove, and then press T to uncheck the
box.
To save your new settings:
Highlight Done and press T.
Note: A video preview of the currently highlighted channel is
provided to assist you in adding/deleting channels.
provided to assist you in adding/deleting channels.
To revert to your original settings:
Highlight Cancel and press T before saving.
To remove all channels from the channel memory:
Highlight Reset and press T, and then highlight Done
and press T.
and press T.
To remove encrypted channels from the channel
memory:
memory:
If an encrypted channel is accidentally added to the
channel list by programming channels, you can remove
the unwanted encrypted (non-viewable) channel while
you are channel surfing. When you tune into an
encrypted channel, the following message will appear.
channel list by programming channels, you can remove
the unwanted encrypted (non-viewable) channel while
you are channel surfing. When you tune into an
encrypted channel, the following message will appear.
Press 1 while the message is on the screen to remove
the unnecessary channel from the channel list.
the unnecessary channel from the channel list.
Setting the Auto Input feature
This feature allows you to change TV inputs using the
MODE SELECT
MODE SELECT
buttons—TV, CABLE/SAT, DVD, VCR/
PVR
—on the remote control. Once an input has been set
for a specific MODE SELECT button, the TV will
automatically switch to the input when you press and
hold the MODE SELECT button for 2 seconds.
Auto Input settings options for each MODE SELECT
button are shown below.
automatically switch to the input when you press and
hold the MODE SELECT button for 2 seconds.
Auto Input settings options for each MODE SELECT
button are shown below.
•
TV
: ANT/CABLE
•
CABLE/SAT
: ANT/CABLE, Video 1, Video 2,
ColorStream HD1, ColorStream HD2, HDMI 1, HDMI
2, HDMI 3, HDMI 4, PC
2, HDMI 3, HDMI 4, PC
•
DVD
: Video 1, Video 2, ColorStream HD1,
ColorStream HD2, HDMI 1, HDMI 2, HDMI 3, HDMI
4, PC
4, PC
•
VCR/PVR
: ANT/CABLE, Video 1, Video 2,
ColorStream HD1, ColorStream HD2, HDMI 1, HDMI
2, HDMI 3, HDMI 4, PC
2, HDMI 3, HDMI 4, PC
Note: The TV mode select button will be restricted to the ANT/
CABLE input.
CABLE input.
To set Auto Input:
1
From the Preferences menu, highlight Auto Input
and press T.
and press T.
ANT/CABLE Cable
Scanning channels, please wait ...
Number of Channels Found - 52
Scanning Analog Channels
Found Channel - 55
Cancel
5%
Digital Channel Is Encrypted - Press 1 on remote to remove channel
(continued)
52XV545U_EN.book Page 37 Monday, August 4, 2008 10:54 AM