Руководство Пользователя для Toshiba 42XV545U
61
XV545U (E/F) Web 177.8:228.6
Chapter 6: Using the TV’s features
Using the HDMI settings feature
This menu consists of the following items (new HDMI
capabilities) and will be grayed out on non-HDMI
inputs.
Some HDMI legacy sources may not work properly with
your HDMI TV, please try setting the following options
(Lip-Sync Latency, Deep Color, and x.v.Color) to Off.
Adjusting these settings should allow your HDMI legacy
source to operate properly with your TV.
capabilities) and will be grayed out on non-HDMI
inputs.
Some HDMI legacy sources may not work properly with
your HDMI TV, please try setting the following options
(Lip-Sync Latency, Deep Color, and x.v.Color) to Off.
Adjusting these settings should allow your HDMI legacy
source to operate properly with your TV.
Note: You must disconnect your source device first before
settings can be adjusted.
settings can be adjusted.
•
Lip-Sync Latency: On
This option activates an auto audio/video display
timing adjustment function that allows HDMI source
devices to accurately perform synchronization
automatically.
This option activates an auto audio/video display
timing adjustment function that allows HDMI source
devices to accurately perform synchronization
automatically.
•
Deep Color: On
This feature allows the HDMI source to increase
available colors bits within the boundaries defined by
the RGB or YCbCr color space.
This feature allows the HDMI source to increase
available colors bits within the boundaries defined by
the RGB or YCbCr color space.
•
x.v.Color: On
This feature expands the color range (limits) of HDMI
signals. This allows for the sending of wider color
signals from the HDMI source.
This feature expands the color range (limits) of HDMI
signals. This allows for the sending of wider color
signals from the HDMI source.
All of the above HDMI settings need proper HDMI
source devices. If an HDMI source device does not
support these features, the TV may not work properly
when these features are enabled.
source devices. If an HDMI source device does not
support these features, the TV may not work properly
when these features are enabled.
Note: If your HDMI connection is capable of 1080p and/or
your TV is capable of refresh rates greater than 60Hz or
supports Deep Color, you will need a High Speed HDMI cable.
Conventional HDMI/DVI cables may not work properly with this
mode.
your TV is capable of refresh rates greater than 60Hz or
supports Deep Color, you will need a High Speed HDMI cable.
Conventional HDMI/DVI cables may not work properly with this
mode.
To set the HDMI Settings:
1
Select the appropriate HDMI input mode (HDMI 1,
HDMI 2, HDMI 3, or HDMI 4).
HDMI 2, HDMI 3, or HDMI 4).
2
From the Setup menu, highlight HDMI Settings and
press T.
press T.
3
Press B or b to highlight the item you want to set.
4
Press C or c to select On or Off .
5
To save the new settings, highlight Done and press
T. To revert to the factory defaults, highlight Reset
and press T.
and press T.
Displaying TV status information
To display TV status information using RECALL:
Press E on the remote control.
The following information will display (if applicable):
The following information will display (if applicable):
•
Current input (ANT/CABLE, Video 1, etc.)
•
If ANT/CABLE is the current input, either “CABLE”
(for cable TV) or “ANT” (for over-the-air broadcasts).
(for cable TV) or “ANT” (for over-the-air broadcasts).
•
Channel number (if in ANT/CABLE mode)
•
Channel label (if set)
•
Digital signal strength indicator (bar graph in lower
right corner of box; for ATSC signal only)
right corner of box; for ATSC signal only)
•
Stereo, Mono or SAP audio status (when HDMI input
mode, Dolby Digital or PCM)
mode, Dolby Digital or PCM)
•
Video resolution
•
Aspect ratio of incoming video signal (4:3 or 16:9)
•
V-Chip rating status
•
GameTimer (if set)
•
x.v.Color status of incoming signal
To close the RECALL screen:
Press E again.
To display TV status information using INFO:
(only available for ANT/CABLE input)
Press Q on the remote control.
The following additional information will display for off
air digital channels (if applicable):
Press Q on the remote control.
The following additional information will display for off
air digital channels (if applicable):
•
Title
•
Duration
•
Detailed description
To display Next information, press Q on the remote
control again. Pressing Q a third time will remove the
entire banner.
control again. Pressing Q a third time will remove the
entire banner.
Note: The location of the banner can be moved to the top or
bottom of the screen by pressing
bottom of the screen by pressing
B or b while the RECALL or
INFO display is on-screen. (The last position will be stored to
memory.)
memory.)
2-2
ANT
WEATHER
Stereo
NONE
480i
4:3
2-2
ANT
Nashville WX Channel
Nashville WX Channel provides Middle Tenessee and Southern Kentucky
weather.
8:59am - 4:59pm EST
Stereo
480i
4:3
WEATHER
NONE
52XV545U_EN.book Page 61 Monday, August 4, 2008 10:54 AM