Инструкции По Установке для Netopia 2e
3
2
Setting Up Your Cayman 2E
1.
Unpack your Cayman 2E shipping carton.
2.
Position the Cayman 2E.
You should put the Cayman 2E in a location where air can circulate freely around it.
Do not cover the vents on the top of the Cayman 2E.
You should put the Cayman 2E in a location where air can circulate freely around it.
Do not cover the vents on the top of the Cayman 2E.
3.
Connect the LAN (Ethernet A) port on the Cayman 2E to your workgroup
Ethernet network.
Ethernet network.
4.
Connect the WAN (Ethernet B) port on the Cayman 2E to your wide area
network.
For example, connect the WAN port to your cable modem, xDSL modem, or
backbone network.
network.
For example, connect the WAN port to your cable modem, xDSL modem, or
backbone network.
9VDC
WAN 10BT
MAINTENANCE
CONSOLE
LAN 10BT
To Your
Local Area Network
9VDC
WAN 10BT
MAINTENANCE
CONSOLE
LAN 10BT
To Your
Wide Area Network
(Cable Modem, xDSL Modem)
5.
Connect the power transformer to the power jack on the Cayman 2E back
panel. Plug the power transformer into an appropriate electrical outlet.
panel. Plug the power transformer into an appropriate electrical outlet.
Note: At this point, if your Cayman 2E can obtain network information from a DHCP server on
its WAN interface, your Cayman 2E is completely functional. If a DHCP server is not available,
you must configure the IP address information on the Cayman 2E WAN port (see page 4).
Because the operating software for your Cayman 2E is installed during factory verification, you
do not need to run the Cayman 2E installer utility before using the device.
its WAN interface, your Cayman 2E is completely functional. If a DHCP server is not available,
you must configure the IP address information on the Cayman 2E WAN port (see page 4).
Because the operating software for your Cayman 2E is installed during factory verification, you
do not need to run the Cayman 2E installer utility before using the device.
The following instructions assume that you want all devices on your workgroup Ethernet
network to use IP addresses on the 192.168.1.0 network. If your workgroup network must
use another network number, refer to the Cayman 2E documentation for information on
how to change the IP address of the LAN interface for the Cayman 2E.
network to use IP addresses on the 192.168.1.0 network. If your workgroup network must
use another network number, refer to the Cayman 2E documentation for information on
how to change the IP address of the LAN interface for the Cayman 2E.
1.
Configure your computer to use an IP address on the same TCP/IP network as
the Cayman 2E.
the Cayman 2E.
•
Windows 95/Windows 98/Windows NT
1 Open the Network Control Panel and select the TCP/IP service for the
Ethernet card in your computer (for example, TCP/IP ->3Com EtherLink III).
2 Open the Properties window.
3 Click the Gateways tab, and remove any installed gateways.
4 Click the DNS Configuration tab, and disable DNS.
5 Click the IP Address tab, and click the Obtain an IP Address Automatically
option button.
6 Click OK to save the modified TCP/IP settings.
•
Macintosh – If your Macintosh uses Open Transport, open the TCP/IP Control
Panel and choose Connect via Ethernet. Choose Configure Using DHCP Server
and enter the IP address of the Cayman 2E (192.168.1.254) in the Name Server
Address text box.
Panel and choose Connect via Ethernet. Choose Configure Using DHCP Server
and enter the IP address of the Cayman 2E (192.168.1.254) in the Name Server
Address text box.
If your Macintosh uses MacTCP, open the MacTCP Control Panel and select the
Ethernet interface icon. Enter 192.168.1.x (where x is any number in the range 1-
253) in the IP Address text field. Click the More button. Click the Obtain Address
Manually radio button. Enter 192.168.1.254 in the Gateway Address text field.
Pull down the Class dropdown list and choose C, which sets your subnet mask
to 255.255.255.0. In the Domain Name Server Information fields, enter your
Internet Service Provider’s domain name in the Domain text field and enter
192.168.1.254 in the IP Address text field.
Ethernet interface icon. Enter 192.168.1.x (where x is any number in the range 1-
253) in the IP Address text field. Click the More button. Click the Obtain Address
Manually radio button. Enter 192.168.1.254 in the Gateway Address text field.
Pull down the Class dropdown list and choose C, which sets your subnet mask
to 255.255.255.0. In the Domain Name Server Information fields, enter your
Internet Service Provider’s domain name in the Domain text field and enter
192.168.1.254 in the IP Address text field.
2.
Restart your computer.
3.
Configure each computer that will use the Cayman 2E’s address sharing
feature to use DHCP, as described in Step 1, above.
Configure devices that will not use DHCP with static IP addresses on the same
network as the Cayman 2E. Restart each device after you have updated its TCP/IP
configuration.
feature to use DHCP, as described in Step 1, above.
Configure devices that will not use DHCP with static IP addresses on the same
network as the Cayman 2E. Restart each device after you have updated its TCP/IP
configuration.
Configuring Your Computer