Краткое Руководство По Установке для Netopia 4686-XL
Netopia
®
4686-XL
Cable/DSL Router
Quickstart Guide
C
C
C
Ch
h
h
hee
e
ecccckk
k
k yyy
yo
o
o
ou
u
u
urrrr p
p
p
paa
a
acccckk
k
kaa
a
ag
g
g
gee
e
e cccco
o
o
on
n
n
nttttee
e
en
n
n
nttttssss::::
1.
After unpacking your Netopia Router shipping carton, decide where you want
to locate the Router.
You should install the Router near your PC or another location that permits easy access
and visibility. You can lay the Netopia Router flat or mount it on a wall. Make sure any
Ethernet cables are kept away from power cords, fluorescent lighting fixtures, and
other sources of electrical interference. Put the Router in a location where air can circu-
late freely around it.
2.
Connect the power transformer to the power jack on the Router back panel.
Plug the power transformer into an appropriate electrical outlet. Turn the
power ON with the power switch.
power ON with the power switch.
The
Power
light should come on solid green.
3.
Connect the Router to the Ethernet jack on your cable modem or DSL modem.
Be sure your DSL or cable modem is installed according to its instructions, and con-
nected to its appropriate wall jack. Insert one end of the gray modem cable in the
M
M
M
Mo
o
o
od
d
d
dee
e
em
m
m
m
port on the Netopia Router back panel. Insert the other end of the modem
cable into the Ethernet jack on your DSL or cable modem.
The
Modem
indicator light should come on solid green.
4.
• Connect the Router to create your Ethernet local area network (LAN.)
• Connect each computer or other device to the Router using standard Ethernet cables.
(A yellow Ethernet cable is supplied.) If you have more than four devices to connect,
you can connect an Ethernet hub or switch to one of the 4686-XL’s switch ports, and
connect your remaining devices to the Ethernet hub or switch.
• An
Ethernet
light should come on solid green for each connected Ethernet port.
• Each computer should be configured to obtain its IP address via DHCP from the
4686-XL. See
“Configure Your PC for Dynamic Addressing”
on page 4.
Note:
You need not connect the Dial Up port or the Console port at this time. You
may wish to connect them later. See the Getting Started Guide on your Netopia CD for
instructions.
• If your PC needs to have its network settings changed, proceed to
“Configure Your
PC for Dynamic Addressing”
on page 4.
When all of your connections are made, the status LEDs on the front of your Netopia Router
will light, according to the following diagram:
will light, according to the following diagram:
Checklist
Netopia Router
CD & Quickstart
Guide
Guide
Power
Supply
Supply
Gray RJ-45
Modem
Cable
Modem
Cable
Yellow RJ-45
Ethernet
Cable
Ethernet
Cable
Set up your Router
Power
Console
Off / On
O / I
LAN
Dial Up
4
WAN
1
2
3
DSL or Cable
DC Power
2
3
4
4686-XL Rear View
Modem
Modem
Port
Ethernet
Ports
Power Switch
Power -
LAN 1, 2, 3, 4 -
Modem -
Flash
green
when there is
activity on the LAN.
4686-XL Front View
Flashes
green
for activity
on the modem port.
Solid
green
when connected.
Solid
green
when connected.
Green
when power is on.
Dial Up -
Flashes
Flashes
green
when there is
activity on the internal modem.
1
2
3
B
ROADBAND
WITHOUT
B
OUNDARIES
®