Справочник Пользователя для Netopia ter
5
C
ONNECTING
TO
YOUR
N
ETWORK
The Netopia Router in a 10Base-T network
B
EFORE
RUNNING
S
MART
S
TART
The Smar tStar t Wizard will help you set up the router and let other users on the local area network (LAN) share the Internet connection. The
Smar tStar t Wizard walks you through a series of questions and based on your responses automatically configures the router for connecting your
LAN to the Internet or to your remote corporate network.
Smar tStar t Wizard walks you through a series of questions and based on your responses automatically configures the router for connecting your
LAN to the Internet or to your remote corporate network.
The Smar tStar t Wizard will:
n
automatically check your Windows 95, 98, or NT PC’s TCP/IP configuration to be sure you can accept a dynamically assigned IP address, and
change it for you if it is not set for dynamic addressing
change it for you if it is not set for dynamic addressing
n
check the physical connection from your computer to your router without your having to enter an IP address
n
assign an IP address to your router
n
allow you to enter your dial-up telephone numbers or other information
n
dial up and test your connection to your chosen ISP or other remote site
Be sure you have connected the cables and power source as described in “Making the Physical Connections” on page 4.
Before you launch the Smar tStar t application, make sure your computer meets the following requirements:
Crossover switch
A crossover switch with Normal and Uplink positions. If you use Ethernet Por t #1 for a direct Ethernet connection
between a computer and the router, set the switch to the
between a computer and the router, set the switch to the
Normal
position. If you are connecting the router to an
Ethernet hub, use Ethernet por t #1 on the router and set the switch to the
Uplink
position.
8-por t Ethernet hub
Eight Ethernet jacks. You will use one of these to connect to the Netopia Router for configuration. For a new instal-
lation with Smar tStar t, use the Ethernet connection. You can either connect your computer directly to any of the
Ethernet por ts on the router, or connect both your computer and the router to an existing Ethernet hub on your LAN.
Alternatively, you can use the console connection with a terminal emulator application and a direct serial connec-
tion, or Telnet via Ethernet, to run console-based management. See the on-line
lation with Smar tStar t, use the Ethernet connection. You can either connect your computer directly to any of the
Ethernet por ts on the router, or connect both your computer and the router to an existing Ethernet hub on your LAN.
Alternatively, you can use the console connection with a terminal emulator application and a direct serial connec-
tion, or Telnet via Ethernet, to run console-based management. See the on-line
User’s Reference Guide
on your
Netopia CD.
S/T Termination
switch
switch
Netopia Router S/T models also provide an S/T termination switch. The S/T termination switch on the Netopia
Router back panel must be enabled to terminate the S/T bus. To enable this parameter, the switch must be toggled
to the left, which is the default setting.
Router back panel must be enabled to terminate the S/T bus. To enable this parameter, the switch must be toggled
to the left, which is the default setting.
2 Phone por ts
(POTS models only)
(POTS models only)
Netopia Router models that suppor t Smar tPhone™ provide two RJ-11 telephone jacks for connecting analog
devices, such as a telephone, facsimile machine, or modem.
devices, such as a telephone, facsimile machine, or modem.
PC
Macintosh
System software
Windows 95, 98, or NT operating system
MacOS 7.5 or later
Connectivity
software
software
TCP/IP must be installed and properly configured.
See “Configuring TCP/IP on Windows 95, 98, or NT
computers” on page 10
See “Configuring TCP/IP on Windows 95, 98, or NT
computers” on page 10
MacTCP or Open Transpor t TCP/IP must be installed and properly
configured. See “Configuring TCP/IP on Macintosh computers” on
page 11.
configured. See “Configuring TCP/IP on Macintosh computers” on
page 11.
Connectivity
hardware
hardware
Ethernet card or transceiver (10Base-T)
Either a built-in or third-par ty Ethernet card or transceiver (10Base-T)
Browser
software
software
Netscape Communicator™ or Microsoft Internet Explorer, included on the Netopia CD. Required for web-based registra-
tion and web-based monitoring.
tion and web-based monitoring.
Notes:
•
•
The computer running Smar tStar t must be on the same Ethernet cable segment as the Netopia Router.
Repeaters, such as 10Base-T hubs between your computer and the Netopia Router, are acceptable, but devices such as switches or other
routers are not.
• Smar tStar t for the PC will offer to set your TCP/IP control panel to “Obtain an IP address automatically” if it is not already set this way. This
will require you to reboot your computer. If you have a specified IP address configured in the computer, use the Smar tStar t advanced config-
uration option (see “Advanced option” on page 9) to change your Netopia default IP address (192.168.1.1). You should make a note of it
before running Smar tStar t, in case you do not want to use the dynamic addressing features built in to the Netopia Router and need to
restore the fixed IP address.
routers are not.
• Smar tStar t for the PC will offer to set your TCP/IP control panel to “Obtain an IP address automatically” if it is not already set this way. This
will require you to reboot your computer. If you have a specified IP address configured in the computer, use the Smar tStar t advanced config-
uration option (see “Advanced option” on page 9) to change your Netopia default IP address (192.168.1.1). You should make a note of it
before running Smar tStar t, in case you do not want to use the dynamic addressing features built in to the Netopia Router and need to
restore the fixed IP address.
Port
Description
Ether
8
4
4
1
Nor
To connect your 10Base-T network to the Netopia Router through an
Ethernet por t, use a 10Base-T cable with RJ-45 connectors.
Ethernet por t, use a 10Base-T cable with RJ-45 connectors.
If you have more than eight devices to connect, you can attach
additional devices using either a 10Base-T hub or an EtherWave daisy
chain, or some combination of both.
additional devices using either a 10Base-T hub or an EtherWave daisy
chain, or some combination of both.
If you add devices connected through a hub, connect the hub to
Ethernet por t number 1 on the Netopia Router and set the
Normal/Uplink switch to Uplink.
Ethernet por t number 1 on the Netopia Router and set the
Normal/Uplink switch to Uplink.