Дополнительное Руководство для Crown ct-1600
Com-Tech 200 Amplifier Service Manual
27
Q42969-8 Output Module (P10337-7 board) Parts List
Capacitors
C01
C 8511-5
.047µF 250V Ax
C02
C 8426-6
.1µF
C03
C 8426-6
.1µF
C04
C 6805-3
.022µF
C05
C 6805-3
.022µF
C06
C 6806-1
.01µF 100V Ax
C07
C 6807-9
.001µF 100V Ax
C08
C 6810-3
180pF
C09
C 6809-5
220pF
C10
C 7697-3
.01µF
C11
C 7697-3
.01µF
C43
C 7697-3
.01µF
Diodes
D01
C 2851-1
1N4004
D02
C 2851-1
1N4004
D03
C 2851-1
1N4004
D04
C 2851-1
1N4004
D05
C 2851-1
1N4004
D06
C 2851-1
1N4004
D07
C 2851-1
1N4004
D08
C 2851-1
1N4004
D09
C 2851-1
1N4004
D10
C 2851-1
1N4004
D11
C 2851-1
1N4004
D12
C 2851-1
1N4004
Inductors
L00
C 6592-6
1.3µH Output Coil
L01
C 3510-2
470µH
L02
C 3510-2
470µH
Transistors
Q17
C 8508-1
NPN 2SC3298B
Q19
C 8509-9
PNP 2SA1306B
Note: Q18, S100, Driver Transistors, and Output Tran-
sistors are not included with the Output Module. See
Output Assembly parts list for part numbers.
sistors are not included with the Output Module. See
Output Assembly parts list for part numbers.
Resistors
R00
A10266-4711
470
R01
A10266-1011
100
R04
C 6486-2
.2 5W
R07
C 6486-2
.2 5W
R10
A10266-1011
100
R11
A10266-2R73 2.7 1W
R12
A10266-2R73 2.7 1W
R13
A10266-4711
470
R14
A10266-2R73 2.7 1W
R16
C 6486-2
.2 5W
R19
C 6486-2
.2 5W
R23
C 6844-2
250 Pot LS Bias
R24
A10266-1331
13K
R25
A10266-2221
2.2K
R26
C 6844-2
250 Pot HS Bias
R27
A10266-3911
390
R28
A10266-1331
13K
R29
A10266-5101
51
R30*
A10265-10201* 102*
R31
C 3614-2
15 .5W Flame Proof
R32
C 3614-2
15 .5W Flame Proof
R33
C 7779-9
22 .5W Flame Proof
R34
C 7779-9
22 .5W Flame Proof
Misc.
Board
P10337-7
Jumpers
C 5868-2
0 Ohm .25W
Clips
D 6414-3
Q17/Q19 Hold Down
J500
J600
C 7057-0
10 Pin Header
*Note: R30 is 102 Ohms in most units, though in some
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).