Руководство Пользователя для Dwin transvision
- 6 of 23 -
Programming SL-8000 Remote Control to Operate the TransVision™
The TransVision™ is shipped with a factory pre-programmed remote control.
q
To program the SL-8000 for TransVision™:
1. Press the TV and the MUTE buttons simultaneously. SET will appear on the LCD.
2. Enter the TransVision™’s brand code: 177.
3. Press TV to complete the programming.
2. Enter the TransVision™’s brand code: 177.
3. Press TV to complete the programming.
To operate other audio and video devices refer to the “SL-8000 Operating Manual.”
Installation of the Controller
115 VAC 60 Hz
65 WATTS MAX.
2
2
/
RED GREEN BLUE
+12 VDC
100 mA
TransVision™ Controller Rear Panel
1
2
3
1
1
1
1
V1
V2
Y1
Y2
VIDEO INPUTS
4
RGBS
2
INPUT
2
1
1
1
1
Cr1
Cr2
Cb1
Cb2
5
7
6
RS232
CONTROL
"
"
"
"
"
"
"
"
S1
S2
/
RY1
RY2
2
2
SYNC CONTROL
OUTPUTS
1
1
1
1
Y3
Y3
Cr3
Cb3
RGBS
1
INPUT
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
8
1.
Switched +12VDC Outputs, RY1, RY2
2.5mm DC Plug
2.
Red, Green, Blue, Sync and Control Outputs BNC
3.
RGBS Computer Inputs
15 pin HD Socket
4.
RS-232 Computer Input
9 pin D Plug
5.
S-Video Inputs ( S1, S2 )
4 pin Mini-Din
6.
Composite Video Inputs ( V1, V2 )
RCA Type
7.
Component Video Inputs (Y1, Cr1, Cb1)
RCA Type
(Y2, Cr2, Cb2)
(Y3, Cr3, Cb3)
(Y3, Cr3, Cb3)
8.
AC Power Receptacle .
1. SWITCHED +12VDC OUTPUTS
The TransVision™ has two switched +12 VDC outlets labeled as RY1 and RY2. These outlets may be
used to trigger a relay in an electric screen, projector lift or other relay activated device. See “Relay
Setup” menu for more details.
used to trigger a relay in an electric screen, projector lift or other relay activated device. See “Relay
Setup” menu for more details.
2. RED, GREEN, BLUE, SYNC & CONTROL OUTPUTS
The output video signal from the Controller to the DLP™ projector is made by five 75 Ohm coaxial
cables with BNC connectors for RED, GREEN, BLUE, SYNC and CONTROL outputs. The CONTROL
cable is used to transmit bi-directional control signals between the projector and the Controller unit. The
CONTROL cable must be connected in order for the system to function properly.
cables with BNC connectors for RED, GREEN, BLUE, SYNC and CONTROL outputs. The CONTROL
cable is used to transmit bi-directional control signals between the projector and the Controller unit. The
CONTROL cable must be connected in order for the system to function properly.
q
To test the connection:
1. Press INFO on the remote.
1. Press INFO on the remote.
The screen will display either “Controller connected” or “Controller not connected.”
3. RGBS INPUTS
3. RGBS INPUTS