Инструкции По Установке для Frigidaire fak127p1v
Casement Window Installation
This air conditioner is designed to fit into most casement type windows.
As shipped from factory, unit will fit into a minimum window opening
15 1/2” wide and 22” hi gh. The preferred method of installation is
through a closed or stationary window. Installation in an open window
frame is also possible where open window can be secured to outside of
building or removed completely.
1.Closed or stationary window: Install unit in stationary sash to avoid
crank handles or window latches. If unit is to be installed in or next to a
movable sash, it may be necessary to remove catch, handle or both.
Remove crank handle and secure window in closed position. Remove
glass panes and separating strips to a height sufficient to mount unit.
2.Open window frame: Remove crank mechanism and catch handles.
Fold window sash back against exterior wall of building and secure, or
remove completely where possible.
3.A filler panel will be required at side of unit when installed in windows
having width greater than 15 1/2". Filler panel should be made from
3/4” thick wood securely anchored to one side of opening so that
15 1/2” wide opening is provided. Filled panel should run full length
of window. Paint to suit.
4. Install unit in same manner as described for sliding windows.
As shipped from factory, unit will fit into a minimum window opening
15 1/2” wide and 22” hi gh. The preferred method of installation is
through a closed or stationary window. Installation in an open window
frame is also possible where open window can be secured to outside of
building or removed completely.
1.Closed or stationary window: Install unit in stationary sash to avoid
crank handles or window latches. If unit is to be installed in or next to a
movable sash, it may be necessary to remove catch, handle or both.
Remove crank handle and secure window in closed position. Remove
glass panes and separating strips to a height sufficient to mount unit.
2.Open window frame: Remove crank mechanism and catch handles.
Fold window sash back against exterior wall of building and secure, or
remove completely where possible.
3.A filler panel will be required at side of unit when installed in windows
having width greater than 15 1/2". Filler panel should be made from
3/4” thick wood securely anchored to one side of opening so that
15 1/2” wide opening is provided. Filled panel should run full length
of window. Paint to suit.
4. Install unit in same manner as described for sliding windows.
Installation in wood sliding or wood
casement windows
1.For wood frame casement windows, it is necessary to construct a
frame, using at least 1 " thick wood with a 15 1/2" wide opening.
2.Paint frame and fasten it securely, sealing it into window opening.
3.Install unit into frame following procedures for metal sliding and
casement windows.
frame, using at least 1 " thick wood with a 15 1/2" wide opening.
2.Paint frame and fasten it securely, sealing it into window opening.
3.Install unit into frame following procedures for metal sliding and
casement windows.
These installations are also typical, and since styles and sizes of
casement windows vary widely, it is advisable to have unit installed
by someone skilled in this type of installation. The dealer selling these
units can recommend or supply qualified people to install your new unit.
casement windows vary widely, it is advisable to have unit installed
by someone skilled in this type of installation. The dealer selling these
units can recommend or supply qualified people to install your new unit.
Caution: Do not block air circulation to outside louvers
of cabinet.
5
3/8
” long screws
Drilled holes
Speed clips
Channel
Foam seal
Window channel frame
Support platform
Drilled holes
Bottom bar
3/8
” long screws
12.Install speed clips on top and bottom inside edge of window
to provide locking.(See fig. F)
13.Using supplied plastic foam seal, cut to proper length,
insert between inside window sash and outside window.
(See fig. F)
14.Place top retainer on top edge of filler panel, then place
the bottom edge of filler panel into groove of bottom retainer
(mounted on unit). Filler panel may be trimmed with knife or
scissors to fit window height.(See fig. D)
15.Slide sliders upward making sure filler panel aligns in
sliders.
16.With sliders up against top retainer, drill 1/8" hole through
window frame in alignment with existing hole in slider. Install
3/8" long self-threading screw in hole. Repeat for other
slider.
17.Check all seals and plug for air leaks around unit. Use
sealant to fill any minor openings.
to provide locking.(See fig. F)
13.Using supplied plastic foam seal, cut to proper length,
insert between inside window sash and outside window.
(See fig. F)
14.Place top retainer on top edge of filler panel, then place
the bottom edge of filler panel into groove of bottom retainer
(mounted on unit). Filler panel may be trimmed with knife or
scissors to fit window height.(See fig. D)
15.Slide sliders upward making sure filler panel aligns in
sliders.
16.With sliders up against top retainer, drill 1/8" hole through
window frame in alignment with existing hole in slider. Install
3/8" long self-threading screw in hole. Repeat for other
slider.
17.Check all seals and plug for air leaks around unit. Use
sealant to fill any minor openings.
F
F
The above installations are intended to be permanent, and
when installed in apartment or rental properties,
permission to make the above modifications should be
obtained from owners or landlords of buildings prior to
installation of unit.
E
E