Справочник Пользователя для Panasonic sdr-sw21

104

VQT2A17

105

VQT2A17

Use the supplied AC adaptor.
If the battery itself is too hot or too cold, it may take time to charge or it may 
not charge at all.
Keep the AC adaptor at least 1 m (3.3 feet) away from the radio. (Interference 
may affect the radio.)
During use, the AC adaptor may make noises internally, however, this is normal.
After use, unplug the AC adaptor from its AC outlet. (Leaving it connected 
consumes 0.3 W [max.] of power.)
Keep the terminals of the AC adaptor clean.

If the LCD monitor fogs up or becomes dirty, wipe it clean with a soft dry cloth.
When the unit is extremely cold, the LCD monitor may be slightly dark 
immediately after turning the power on; however, the normal brightness is 
restored when internal temperature rises.

The LCD monitor is made with high-precision technology; however, black 
spots may appear in displays or stuck pixels (red, blue or green) may occur. 
There is nothing wrong with the monitor.
The LCD monitor pixels are controlled to a 99.99 % degree of accuracy; 
however, dead or stuck pixels may occur in the remaining 0.01 %. These pixel 
defects are not recorded in SD card images, therefore do not worry.

If condensation adheres to the unit, the lens may fog and the unit and SD card 
may not function properly. Avoid sharp changes in temperature and humidity.
Condensation may adhere in the following cases:

After summer rain showers or in humid places where the air is thick with 
steam
When heaters are turned on in cold rooms
When moving from cold places to warm places
When the unit is directly exposed to cold drafts (i.e., air-conditioners, etc.) 

In the event of differences in temperature or humidity, place the unit in a 
plastic bag, remove as much air as possible, seal and let it sit for about 1 hour 
to adjust to the ambient temperature.
If the lens fogs up, remove the battery and disconnect the AC adaptor, open 
the card/battery door and let it sit for about 1 hour to adjust to the ambient 
temperature.

●
●

●

●
●

●

●
●

●

●

•

•
•
•

●

●

Remove the battery and disconnect the AC adaptor.
Do not use benzene, thinner, alcohol, etc. (These substances can cause 
deformation and peeling.)
Wipe off fingerprints and dust with a soft dry cloth. For stubborn dirt, soak a 
cloth in water, wring it out well, and use it to wipe the dirty surfaces. Then wipe 
the surfaces with a dry cloth.
Use chemically treated tissues in accordance with warnings and indications.

The waterproofing and dustproofing of this unit comply with IP58 of IEC 60529 
“Degrees of protection provided by enclosures (IP Code)”. It is capable of 
photography underwater at a depth of 2.0 m (6.5 feet) for up to 30 minutes. 
(This means that the unit can be used underwater when handled as stipulated 
by Panasonic, for the specified duration, and at the specified water pressure. It 
is not guaranteed that the unit will not be damaged or malfunction.)

This product has passed drop tests from a height of 1.2 m (4 feet) in 
conformance with “MIL-STD 810F Method 516.5—Shock,” but this does not 
guarantee that the unit will not incur damage, nor malfunction, or be waterproof 
under all conditions. 

(Panasonic test methodology)
Drop height: 1.2 m (4 feet), drop surface: 5 cm (2˝) thick plywood panel 
(lauan), drop orientation: (5 units (maximum)) total 26 orientations, including 
sides, edges, and corners, drop count: 1 drop test for each orientation, final 
judgment criteria: examination of electrical and mechanical performance based 
on product specifications without any consideration given to cases of external 
deformation, such as paint peeling, at impact points. 

●
●

●

●

5

(cont.)