Руководство Пользователя для Hisense kf-2302gwe
4
3 - 2 . M a k e a Ho l e
(1) P lace t he r ear p a nel f rom t he i n door u nit
on the wal l a t t h e l o c a t i on selected.
Make su r e t h e p a n el is horizon t a l , u s i n g
Make su r e t h e p a n el is horizon t a l , u s i n g
,
a c a r p e nter s l e v e l or t a p e measure t o
measu r e down from t he c e i l i ng. W a i t u n t i l
after cu t t i n g t h e h o l e b e f ore attaching
the re a r p anel t o t he wa l l .
measu r e down from t he c e i l i ng. W a i t u n t i l
after cu t t i n g t h e h o l e b e f ore attaching
the re a r p anel t o t he wa l l .
(2)Determi n e w h i c h s i d e o f t h e u nit you
shoul d make the hole f o r t u b i n g a n d
NOTE
In the case of left-rear tubing, use the outside
mark for precise placement of the hose outlet.
(Fig.5d)
(3)Before making the hole, check carefully that no
studs or pipes are directly run behind the spot
to be cut.
to be cut.
CAUTION
Also avoid areas where elec-
trical wiring or conduits are
located.
trical wiring or conduits are
located.
The above preca u t i o n s a r e a l s o a pplicable
if tubing g o e s t h r o u g h the wall in a n y
other lo c a t i on.
if tubing g o e s t h r o u g h the wall in a n y
other lo c a t i on.
( 4 ) U sing a sabre saw , k e y h o l e s a w o r h o le-
cutting d r i l l a ttachment, c u t a hole in
Table 2
H o l e D ia.(mm )
6 5
(5) M easure t he t h i c k n ess o f t he w all f r o m t h e
i n s i d e e dge to the outsi d e e d g e a n d c ut PVC
p i p e at a s l i g h t a n g l e 6 m m s h o r t e r t h a n
t h e t hicknes s o f the wa l l.(Fig.7)
p i p e at a s l i g h t a n g l e 6 m m s h o r t e r t h a n
t h e t hicknes s o f the wa l l.(Fig.7)
(6) P l a c e t he p lastic c over o v e r t h e e nd o f t h e
p i p e ( f o r i n d o o r s i d e o n l y ) a n d ins e r t the
p i p e i n th e w all.(Fig . 8 )
p i p e i n th e w all.(Fig . 8 )
3 - 3 . i n s tall th e R ear Pa n e l o n th e w all
B e sure to c o n f i r m that t h e w all is s t r o n g
e n o u gh to s u s pend th e u nit.
( 1 ) A ttach t h e r e a r p an e l t o t h e w a l l w i t h t he
6 nai l s p rovided.( F i g . 9 )
,
( 2 ) D ouble check with a r u l e r o r c a r p enter s
level that t h e p a n e l i s level. Thi s i s
i m p o r t a n t
i m p o r t a n t
t o
i n s t a l l
t h e
u n i t
properly. ( F i g . 1 0 )
( 3 ) M ake su r e t h e pane l i s flush a g a i nst the
wall. Any space be t w e e n t h e w a l l a nd unit
will ca u s e n oise an d v ibrat i o n .
will ca u s e n oise an d v ibrat i o n .
Fig. 5b
Rear panel
marks
Right-rear
tubing
(recommended)
tubing
(recommended)
Downward tubing
Right tubing
Left
tubing
tubing
Left rear
tubing
tubing
In case of left-rear, right-rear
Fi g.5d
Hole should be made at a slight downward slant the
outdoor side.
outdoor side.
INSIDE
OUTSIDE
Fig.6
PVC pipe (locally purchased)
Cut at slight angle
Fi g.7
INSIDE
OUTSIDE
Wall
Slight
angle
PVC pipe
Plastic
cover
cover
Fig .8
A n d d r a i n c a p . ( F o r d e t a i l s , r e f e r t o
“ S w i t c h i n g d r a i n h o s e a n d d r a i n c a p” o n
“ S w i t c h i n g d r a i n h o s e a n d d r a i n c a p” o n