Руководство Пользователя для CoxReels spring-driven welding cable reel - 1-ga. cable - p-wc17-5001

Скачать
Страница из 6
                                   INSTALLATION AND MAINTENANCE MANUAL
              FORM #PM-005 REV D 12/09 
Page 3 of 6 
 
For assembly drawings, parts lists, or specific repair instructions, refer to web site at 
www.coxreels.com
 or consult factory. 
Coxreels, Inc., 5865 S. Ash Ave., Tempe, Arizona, USA, 85283    Tel: 1-800-269-7335 
 
 
 
 
 
F
ig. 1.0   
 
 
 
 
 
Fig. 2.0
 
 
NOTE:  On SD models ground path is from end of cable clamp to 
unpainted surface on bottom of reel base. 
 
• 
Loosely fit two pieces of mounting hardware to ceiling/floor/or wall so 
that reel can be slid into position. Fit reel. Install two pieces of 
hardware in other end of reel.  Securely fasten all bolts and nuts. 
 
OPERATIONAL CHECK 
 
• 
Check reel for correct operation by slowly pulling out cable.  A 
clicking noise will be heard after each half revolution of the drum. 
• 
LATCH the reel.  Pull out the cable and allow it to slightly retract after 
the first, second or third “click” is heard. 
• 
UNLATCH the reel. Slowly pull the cable until the clicking noise 
stops, and then allow the cable to retract.  The hose stopper should 
rest against the roller hose guide. 
 
 CAUTION:  DO NOT ALLOW CABLE TO RETRACT WITHOUT 
RESTRAINING RECOIL SPEED.  NEVER LET GO OF THE CABLE 
WHEN REWINDING.  NOTE: EZ-COIL
 MODELS ARE DESIGNED 
TO RETRACT AT A SLOW CONTROLLED SPEED. 
 
• 
Apply power to reel.  Periodically check cable for improper wear. 
• 
Reels are shipped with approximately three pre-wraps of tension. 
This is adequate for most applications.  However, if your application 
requires more or less tension, see “Spring Tension Adjustment” 
instructions. 
• 
Lubrication is NOT required. 
 
 
 
 
 
 
 
 
SPRING TENSION ADJUSTMENT 
• 
Remove power from reel prior to making spring adjustments. 
• 
Pull out approximately 6 feet (2m) of cable and latch the drum. 
• 
Add or subtract one wrap of cable as desired to acquire the proper 
tension on the reel. 
 
NOTE: Spring tension adjustment is accomplished by adding wraps of 
cable around the drum (to increase tension) or subtracting wraps of 
cable (to decrease tension). 
 
 
CAUTION: Improper tensioning of spring or adding too many pre-wraps 
may cause damage to spring mechanism.  Only authorized personnel 
should make adjustments. 
 
• 
Unlatch drum and check for proper tension. 
• Connect 
power 
source. 
 
SPRING CANISTER REPLACEMENT (SD Series) 
 
• 
Pull out approximately 3 feet (1m) of cable and latch the reel. 
• 
Release all spring tension by removing five wraps of cable from reel. 
• 
Carefully unlatch the reel and firmly hold the drum. Allow the drum 
to slowly unwind until it stops. 
• 
Remove two nuts from spring cartridge. (See figure 3.0) 
• 
Pull spring cartridge off center axle shaft. 
• 
Reverse above procedure to re-assemble. 
• 
Re-tension the reel by turning the drum three complete turns and 
latching in place.  Follow “Spring Tension Adjustment” procedure. 
 
 
 
 
Fig 3.0 (SD Reel) 
Fig 4.0 (P-WC Reel)