Руководство Пользователя для Samsung CLP-650
Using Your Printer on a Network (CLP-650N only)
8.3
13
Repeat step 12 to complete the address from the 1st byte
to the 4th byte.
14
To select other parameters, such as the Subnet Mask or
Gateway, press the scroll button (
Gateway, press the scroll button (
or
). Press the
Enter button (
).
15
16
Press the On Line/Continue button (
) to return to
ready mode.
Dynamic Addressing (BOOTP/DHCP)
To assign the TCP/IP address automatically by the server, take
the following steps:
the following steps:
1
In ready mode, press the Menu button (
) until you see
“Network” on the bottom line of the display. Press the
Enter button (
Enter button (
) to access the menu.
2
Press the Enter button (
) when “Config Network”
displays on the bottom line.
3
Press the scroll button (
or
) until “Yes” displays,
and press the Enter button (
).
4
Press the Upper Level button (
), then use the scroll
button (
).
5
Press the Enter button (
) when “Config TCP” displays.
6
Press the scroll button (
or
) until “Yes” displays,
and press the Enter button (
).
7
Press the Upper Level button (
), then use the scroll
button (
).
8
Press the Enter button (
) when “IP Get Method”
displays.
9
Press the scroll button (
or
) until “DHCP” displays,
and press the Enter button (
).
10
To assign the address from the BOOTP server, press the
Enter button (
Enter button (
) when “BOOTP” displays.
11
Press the On Line/Continue button (
) to return to
ready mode.
Configuring IPX Frame Types
On IPX/SPX protocol networks (for example, Novell NetWare),
the format of the network communication frames must be
specified for the printer. In most cases, you can keep the ‘Auto’
default setting. However, you can manually set the frame type
specified for the printer. In most cases, you can keep the ‘Auto’
default setting. However, you can manually set the frame type
format, if required.
• Auto (default): Automatically senses and limits the frame
type to the first one detected.
• EN_8022: Limits the frame type to IPX over IEEE 802.2
with IEEE 802.3 frames. All others will be discarded.
• EN_8023: Limits the frame type to IPX over IEEE 802.3
frames. All others will be discarded.
• EN_II: Limits the frame type to IPX over Ethernet Frames.
All others will be discarded.
• EN_SNAP: Limits the frame type to IPX over SNAP with
IEEE 802.3 frames. All others will be discarded.
Note that the IPX/SPX protocol must be enabled in the
Netware menu before you can configure frame types. See
“Setting Network Protocols” on page 8.2.
“Setting Network Protocols” on page 8.2.
Take the following steps to change the frame type format:
1
In ready mode, press the Menu button (
) until you see
“Network” on the bottom line of the display. Press the
Enter button (
Enter button (
) to access the menu.
2
Press the Enter button (
) when “Config Network”
displays on the bottom line.
3
Press the scroll button (
or
) until “Yes” displays on
the bottom line. Press the Enter button (
).
4
Press the Upper Level button (
).
5
Press the scroll button (
or
) until “Netware”
displays on the bottom line. Press the Enter button (
).
6
Press the scroll button (
or
) until “On” displays on
the bottom line. Press the Enter button (
).
7
Press the Upper Level button (
), then use the scroll
button (
).
8
Press the Enter button (
) when “Config Netware”
displays.
9
Press the scroll button (
or
) until “Yes” displays on
the bottom line. Press the Enter button (
).
10
Press the Upper Level button (
), then use the scroll
button (
).
11
Press the Enter button (
) when “IPX Frame Type”
displays.