Краткое Руководство По Установке для Olympus e-100 rs

1. Set the Mode dial to P.

2. Compose the picture by turning the

camera towards the subject and centering
the AF target mark on the image you want
to shoot.

Press 

(Monitor button) to select whether to

display your image on the Monitor or the Viewfinder.

[To enlarge your subject]
Press the Zoom lever toward “T” to enlarge your subject. To return to normal
magnification, press the Zoom lever back toward “W”.

3. Press the Shutter button halfway to focus.

The AF confirmation mark lights up in green in the
upper left corner and the camera beeps.  Focus
and exposure (shutter speed/aperture) become
locked. 
If the AF confirmation mark blinks, then the camera
is out of focus. If this happens, release the Shutter
button and move the AF target mark slightly.  Then,
press the shutter button halfway again.

4. Press the Shutter button fully to take a

picture.

The free part of the memory gauge lights up and
the card access lamp blinks while the picture is
being recorded.
Continuous shooting is available even if the card
access lamp is blinking, unless the entire memory
gauge is lit.
If you are taking a picture in a dark environment,
the built-in flash will fire automatically if it has been
popped up.

Press
halfway

Press
fully

Viewfinder

AF target mark

AF confirmation mark

AF target mark

Memory gauge

Card access
lamp

Flash mode

Macro mode

Slow shutter
synchronization flash

Auto
bracket

Flash intensity control

Card writing

Sound
record

Card error

Battery check

White balance

Self-timer/
Remote control

ISO

Number of storable
still pictures

Seconds that movies
can be shot

Card

Sequential shooting

Record mode

Pre-capture

AE memory

Stabilizer

Metering mode

Manual focus

AF system

Exposure
compensation

Full-time AF

Set the Mode dial to 

.

The last picture taken is played back.

●

Use the Arrow pad to select the desired picture for display.

: Displays next picture.

: Displays preceding picture.

: Jumps to the picture 10 frames ahead.

: Jumps to the picture 10 frames behind.

*Press the Zoom lever toward “W” to display multiple

pictures at the same time (Index-display).

*Press the Zoom lever toward “T” to display a close-up.

Arrow pad

Still picture display (1-frame)

Index-display

●

Use the Arrow pad to select the desired picture for display.

: Plays movie pictures when held down continuously.

: Plays movie pictures in reverse when held down 

continuously. 

: Jumps to the beginning of the movie.

: Jumps to the end of the movie.

●

Press OK to pause the movie.

Unwanted images can be erased. You can erase one frame or all frames,
depending on your requirements.
To erase an unwanted image, first display it on the screen as described
in “     Displaying pictures” on this page.

Press 

(Erase button) on the camera and

select “YES” on the confirmation screen using
the Arrow pad.  Then, press OK.

Press 

, then select “CARD SETUP”—“

” using the Arrow pad. Press

OK. Select “YES” on the confirmation screen, then press OK again. 
(To cancel, select “NO”, then press OK.)

Confirmation screen

Erasing a still picture

Confirmation screen

When you are finished using the camera, turn the power off after
checking that the card access lamp is not on.

●

The picture on the screen will disappear when you turn the power off.

●

If no operation is performed for 1 minute or more, the image on the screen goes off
automatically to avoid battery exhaustion (this function is called Sleep). To end Sleep,
perform any operation on your camera.

●

When you store the camera, make sure to put the lens cap on. 

1. Set the Mode dial to 

.

The maximum available recording time appears on the Viewfinder.

2. Press the Shutter button fully to start movie recording and press it

again fully to stop.

The card access lamp blinks while the picture is being recorded.
Continuous shooting is available when the card access lamp stops blinking.

will appear with pictures that can be played back as movies.

(1) Press 

(Menu button) to display the Menu.

(2) Select “MOVIE PLAY” and press 

on the Arrow pad.

(3) When “START” appears, press the OK button.

The card access lamp blinks for a moment, then the movie starts.

(4) Press 

when you are finished watching. The Menu reappears. Press 

again to

exit the Menu.

Printed in Japan

䢇

䢇

(Hotline Numbers)
Tel. 01805-67 10 83

for Germany

Tel. 00800-67 10 83 00

for Austria, Belgium, Denmark, France, Netherlands, Norway, Sweden,
Switzerland, United Kingdom

Tel. +49 180 5-67 10 83

for Finland, Italy, Luxemburg, Portugal, Spain, Czech Republic

Tel. +49 40-237 73 899

for Greece, Croatia, Hungaria and the Rest of Europe

Our Hotline is available from 9 am to 6 pm (Monday to Friday)
(E-Mail) di.support@olympus-europa.com