Справочник Пользователя для Pioneer VSX-32
Controlling the rest of your system
09
67
En
Programming signals from other
remote controls
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code.
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code.
1
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons
available are shown below:
learned from other remote controls. The buttons
available are shown below:
1
Press and hold R.SETUP, then press “2” for three
seconds.
The LED flashes continuously.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2
Press the input function button for the component
you want to control.
The LED blinks once and flashes continuously.
The LED blinks once and flashes continuously.
3
Point the two remote controls towards each other,
then press the button that will be doing the learning on
this receiver’s remote control.
The LED blinks once and flashes continuously.
this receiver’s remote control.
The LED blinks once and flashes continuously.
• The remote controls should be 3 cm (1 inch) apart.
4
Press the corresponding button on the other remote
control that is sending (teaching) the signal to this
receiver’s remote control.
If the LED lights for one second, the setting has been
successfully completed.
receiver’s remote control.
If the LED lights for one second, the setting has been
successfully completed.
2
5
To program additional signals for the current
component repeat steps 3 and 4.
To program signals for another component, exit and
repeat steps 2 through 4.
To program signals for another component, exit and
repeat steps 2 through 4.
6
Press R.SETUP to exit the programming mode.
Erasing one of the remote control
button settings
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
restores the button to the factory default.
1
Press and hold R.SETUP, then press “7” for three
seconds.
The LED flashes continuously.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2
Press the input function button corresponding to
the command to be erased, then press ENTER.
The LED flashes once.
The LED flashes once.
3
Press and hold the button to be erased for three
seconds.
If the LED lights for one second, the erasing has been
successfully completed.
If the LED lights for one second, the erasing has been
successfully completed.
4
Repeat step 3 to erase other buttons.
5
Press R.SETUP to exit the erasing mode.
Note
1 The remote can store about 120 preset codes from other components (this has been tested with codes of Pioneer format only).
ZONE 2
ZONE 3
LIGHT
AUTO / ALC /
DIRECT
D.ACCESS
CH LEVEL A.ATT
DIMMER
SIGNAL SEL MCACC
SLEEP
HDMI OUT
TV / DTV
MPX
PQLS
PHASE CTRL
STATUS
THX
PGM
STEREO
iPod CTRL
HOME
MENU
TUNE
TUNE TOOLS
LIST
PRESET
TOP MENU
BAND
GUIDE
T.EDIT
VIDEO
PARAMETER
AUDIO
PARAMETER
ENTER
PRESET
RETURN
CATEGORY
MEMORY
STANDARD
MENU
ADV SURR
AUDIO
INFO
CLASS
ENTER
DISP
HDD
DVD
5
4
6
8
0
7
9
2
1
3
/ CLR
CH
CH
TV CONTROL
INPUT
INPUT SELECT
TV CTRL
iPod USB TUNER
SIRIUS
XM
ADAPTER
NET RADIO
CD
TV
BD
DVD
R.SETUP
SOURCE
RECEIVER MULTI
OPERATION
DVR/BDR
HDMI
RECEIVER
MUTE
MASTER
VOLUME
VOL
2 • Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or
farther apart.
• If the LED flashes for five seconds, it means the memory is full. See Erasing all learnt settings that are in one input function on page 68 to
erase a programmed button you’re not using to free up more memory (note that some signals may take more memory than others).
farther apart.
• If the LED flashes for five seconds, it means the memory is full. See Erasing all learnt settings that are in one input function on page 68 to
erase a programmed button you’re not using to free up more memory (note that some signals may take more memory than others).
3 cm
(1 inch)
This receiver’s
remote control
remote control
Other remote
control
control
VSX-33_UXJCB.book 67 ページ ２０１０年３月９日 火曜日 午前１０時３９分