Справочное Руководство для Epson EMP 8200
1-B C
1-B M
1-B Y
1-B BK
EN
EN
EN
EN
Operation indicator
Lamp indicator
Temperature
indicator
indicator
Setting Up
Adjust the distance between the projector and
the screen until the desired image size is obtained
the screen until the desired image size is obtained
* When installing against wall, leave a space of about
20cm (7.9 in.) between the projector and the wall.
20cm (7.9 in.) between the projector and the wall.
Page 16 of Owner's Manual
screen size
20 cm
(7.9 in.)
*
20 cm
(
7.9 in.
)*
projection
distance
1
1.1–1.4
(3.6–4.6)
1.5–1.8(4.8–6.2)
2.3–2.8
(7.3–9.4)
3.0–3.8 (9.8–12.6)
3.8–4.8 (12.3–15.8)
7.6–9.7 (24.8–31.9)
11.4–14.6 m (37.3–48.1 ft.)
30"
40"
60"
80"
100"
200"
300"
61
X
46
81
X
61
120
X
90
160
X
120
200
X
150
410
X
300
610
X
460 (cm)
Checking the indicators
The projector is equipped with indicators that alert you to problems with projector operation.
The following tables show what the indicators mean and how to remedy problems that they indicate.
The following tables show what the indicators mean and how to remedy problems that they indicate.
*1 If an indicator is showing a status which does not appear in the previous tables,
contact your dealer or nearest address provided at "International
Warranty Conditions" in "Safety Instructions/World-Wide Warranty Terms" included in the package.
*2 Contact your dealer for a spare lamp.
Page 70 of Owner's Manual
Troubleshooting
14
Operation Indicator
Indicator status
Problem and remedy
Illuminated
in Orange
in Orange
Illuminated
in Green
in Green
Blinking
in Orange
in Orange
Blinking
in Green
in Green
Standby condition.
This is the only time when the power cord
can be disconnected.
This is the only time when the power cord
can be disconnected.
Projection will start a few moments after
has been pressed.
has been pressed.
Cool-down in progress.
After while, the projector switches to the
standby condition (the indicator lights orange).
After while, the projector switches to the
standby condition (the indicator lights orange).
Warm-up in progress.
After warm-up is complete, projection
will start when an image signal is input.
After warm-up is complete, projection
will start when an image signal is input.
Blinking
in Red
in Red
Extinguished
Internal problem.
Stop using the projector and ask for projector
to be repaired.
to be repaired.
*1
The power is not switched on.
Projecting in progress.
Temperature Indicator
Indicator status
Problem and remedy
Excessive internal temperature (overheating).
The lamp goes off automatically and projection
becomes impossible. Wait for approximately 5
minutes with the projector in that state. After 5
minutes has passed, pull out the power plug
and re-insert it.
After re-inserting it, press the and turn on
the power again.
becomes impossible. Wait for approximately 5
minutes with the projector in that state. After 5
minutes has passed, pull out the power plug
and re-insert it.
After re-inserting it, press the and turn on
the power again.
Illuminated
in Red
in Red
Extinguished
The power has not been switched on or normal
projection is in progress.
projection is in progress.
Blinking
in Red
in Red
Blinking
in Orange
in Orange
Internal problem.
Stop using the projector and ask for projector
to be repaired.
to be repaired.
*1
High-speed cooling in progress.
If the internal temperature rises any higher,
projection will stop.
If the internal temperature rises any higher,
projection will stop.
Check that the air inlet and exhaust vents are clear
and that the indoor temperature is not too high.
and that the indoor temperature is not too high.
Power
Power
Lamp Indicator
Indicator status
Problem and remedy
Blinking
in Red
in Red
Blinking
in Orange
in Orange
Extinguished
Nearing the time for replacing the lamp.
Prepare a new lamp.
*2
The power has not been switched on or normal
projection is in progress.
projection is in progress.
Lamp error.
Remove the lamp and check if it is broken.
If the lamp is not broken, reinstall it. If the lamp
is broken, replace it with a new lamp.
If the lamp is not broken, reinstall it. If the lamp
is broken, replace it with a new lamp.
*2