Краткое Руководство По Установке для Epson 732c
1
If this is your first time using the remote, make sure its batteries
are installed as shown.
are installed as shown.
You can use the remote control to control the projector. With the USB
cable, you can use the remote as a wireless mouse. For more information
on using the remote control, see your User’s Guide.
cable, you can use the remote as a wireless mouse. For more information
on using the remote control, see your User’s Guide.
Epson is a registered trademark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
Epson disclaims any and all rights in those marks. © 2005 Epson America, Inc. 1/05
Printed in XXXXXXXXX
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
Epson disclaims any and all rights in those marks. © 2005 Epson America, Inc. 1/05
Printed in XXXXXXXXX
Quick Setup
Epson PowerLite 732c/740c
CPD-19397
U
sing the remote control
W
here to get help
Telephone Support Services
To use the Epson PrivateLine
®
Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included in your Start Here
kit. This service is available 6
kit. This service is available 6
AM
to 6
PM
, Pacific Time, Monday through
Friday, for the duration of your warranty period. You may also speak with
a projector support specialist by dialing one of these numbers:
a projector support specialist by dialing one of these numbers:
U.S.:
(562) 276-4394, 6
AM
to 6
PM
, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6
AM
to 6
PM
, Pacific Time,
Monday through Friday
Toll or long distance charges may apply.
Electronic Support Services
Epson provides technical assistance through electronic support services 24
hours a day at http://support.epson.com. For tips, templates, and training for
developing successful presentations go to http://www.presentersonline.com.
hours a day at http://support.epson.com. For tips, templates, and training for
developing successful presentations go to http://www.presentersonline.com.
If you see a blank screen...
If you see a blank screen or the No signal message after turning on
your notebook, check the following:
your notebook, check the following:
Make sure the Power light on the projector is green and not flashing,
and the lens cover is off.
and the lens cover is off.
Press the Source Search button on the projector to select the
computer as the image source.
computer as the image source.
If you’re using a Windows
®
notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be
labelled CRT/LCD or have an icon such as . You may have to
hold down the Fn key while pressing it. Allow a few seconds for
the projector to sync up after changing the setting.
labelled CRT/LCD or have an icon such as . You may have to
hold down the Fn key while pressing it. Allow a few seconds for
the projector to sync up after changing the setting.
If the projector and notebook
don’t display the same image...
don’t display the same image...
If your image displays either on the projector or notebook, but not on
both, check the following:
both, check the following:
Windows
Try using the CRT/LCD or key as described above. On most systems,
this key lets you toggle between the LCD screen and the projector,
or display on both at the same time.
this key lets you toggle between the LCD screen and the projector,
or display on both at the same time.
If that doesn’t work, check your monitor settings to make sure both the
LCD screen and the external monitor port are enabled.
LCD screen and the external monitor port are enabled.
1.
From the Windows Control Panel, open the Display utility.
2.
In the Display Properties dialog box, click the
Settings tab, then click Advanced.
Settings tab, then click Advanced.
3.
The method for adjusting the setting varies;
you may have to click a Monitor tab, then
make sure the external Monitor port is set
as your primary display and/or enabled.
See your notebook’s manual or online help
for details.
you may have to click a Monitor tab, then
make sure the external Monitor port is set
as your primary display and/or enabled.
See your notebook’s manual or online help
for details.
Macintosh
®
OS X
1.
From the Apple
®
menu, select System
Preferences, then select Displays.
2.
Select the VGA Display or Color LCD
dialog box.
dialog box.
3.
Click the Arrangement (or Arrange) tab
and click Mirror Displays.
and click Mirror Displays.
Macintosh OS 9.x or earlier
1.
From the Apple menu, select Control
Panels, then click Monitors or
Monitors and Sound.
Panels, then click Monitors or
Monitors and Sound.
2.
Click the Arrange icon.
3.
Drag one monitor icon
on top of the other.
on top of the other.
If the Arrange option isn’t available, click the
Monitor icon and select a Simulscan resolution.
Monitor icon and select a Simulscan resolution.
T
roubleshooting
Turn off projector
display and sound
Optimize the
computer image
Turn projector on and off
Navigate projector menus
Zoom in on part of
the projected image
the projected image
Choose which source
to display
Control projector volume
Don’t forget to register!
Fill out the registration card included in your Start Here kit and
mail it to Epson. Or register online at www.epson.com /webreg.
mail it to Epson. Or register online at www.epson.com /webreg.