Листовка для Sony UNIOPL7T2
IR Illuminator
(Images 1)
•
Designed for the SNC-RS44/46, SNC-RH124,
SNC-RZ25, SNC-RX, SNC-EP/ER 520/550/580 and
SNC-ZR550/ZP550 series of cameras.
SNC-RZ25, SNC-RX, SNC-EP/ER 520/550/580 and
SNC-ZR550/ZP550 series of cameras.
•
Pressurization seals out condensation,
dust, insects and pollution.
dust, insects and pollution.
•
Superb corrosion protection; excellent for coastal
areas and other extreme environmental conditions.
areas and other extreme environmental conditions.
•
Pressurized to 7 psi.
•
Schraeder valve, and pressure relief valve.
•
The outdoor pressurized dome camera housing shall be a Sony model UNI-OPL7C2 are designed for the Sony SNC-RX,
RH, RS, SNC-RZ25N, SNC-EP/ER or the SNC-ZR550/ZP550 series of cameras. The housing shall be capable of withstanding
a total of 7 psi (48 Kpa) of nitrogen gas injected through a Schraeder valve located on top of the machined stainless
steel plate. A pressure relief valve located across from the Schraeder valve will provide an escape for pressure
a total of 7 psi (48 Kpa) of nitrogen gas injected through a Schraeder valve located on top of the machined stainless
steel plate. A pressure relief valve located across from the Schraeder valve will provide an escape for pressure
exceeding 7 psi (48 Kpa). Two (2) o-ring seals shall be included, 3.5 x 235mm (inner diameter) and 3.5 x 114.3mm
(inner diameter). A 10-pin hermetically sealed connector, located at the top of the pressurized housing shall provide
power, video and control functions. The housing shall be constructed of 3mm durable UV-resistant engineered plastic,
with a UL flame rating of 94-5VA. The lower dome shall be made of an injection molded, 3mm thick, optically clear
thermoplastic polycarbonate. The dome shall be held in place with minimum of (9) fasteners, and a safety cable shall
be provided to hold the dome while servicing. Access to the enclosure shall be from below with (9) captive fasteners
used to press the dome against a sealing o-ring. A twist-off feature shall allow for the final removal of the dome. The
housing shall come standard with pendant mount. A wall mount bracket, Sony model UNI-WMB1 is available. The
housing shall include a camera mounting bracket that integrates a heater and blower. The blower shall draw 1.4W
continuous power. The 50W heater shall turn on at 60°F (15°C) and turn off at 80°F (27°C). The housing shall support
a temperature range of -50°F to 120°F (-50°C to 50°C). The unit shall have a weight not to exceed 5kg (without camera)
and dimensions of 14.7 x 11.2 x 11.2 inches (366 x 285 x 285mm). The input voltage is 24VAC and the housing shall
include 24VAC to 12VDC power supply for the camera.
(inner diameter). A 10-pin hermetically sealed connector, located at the top of the pressurized housing shall provide
power, video and control functions. The housing shall be constructed of 3mm durable UV-resistant engineered plastic,
with a UL flame rating of 94-5VA. The lower dome shall be made of an injection molded, 3mm thick, optically clear
thermoplastic polycarbonate. The dome shall be held in place with minimum of (9) fasteners, and a safety cable shall
be provided to hold the dome while servicing. Access to the enclosure shall be from below with (9) captive fasteners
used to press the dome against a sealing o-ring. A twist-off feature shall allow for the final removal of the dome. The
housing shall come standard with pendant mount. A wall mount bracket, Sony model UNI-WMB1 is available. The
housing shall include a camera mounting bracket that integrates a heater and blower. The blower shall draw 1.4W
continuous power. The 50W heater shall turn on at 60°F (15°C) and turn off at 80°F (27°C). The housing shall support
a temperature range of -50°F to 120°F (-50°C to 50°C). The unit shall have a weight not to exceed 5kg (without camera)
and dimensions of 14.7 x 11.2 x 11.2 inches (366 x 285 x 285mm). The input voltage is 24VAC and the housing shall
include 24VAC to 12VDC power supply for the camera.
•
Note: To achieve the increased depth with the aspheric design for optimal camera lens to capsule orientation, the
polycarbonate capsule is slightly angled around the highest section. This creates a “line’, visible to the naked eye, around the
upper most section of the capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is
not typically seen by the camera. However, the Sony RH,RS, RX and ER/EP series of cameras have a 15° tilt. The Sony RZ series of
PTZ cameras are capable of a 25° tilt above horizon.
upper most section of the capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is
not typically seen by the camera. However, the Sony RH,RS, RX and ER/EP series of cameras have a 15° tilt. The Sony RZ series of
PTZ cameras are capable of a 25° tilt above horizon.
KEY FEATURES
BID SPECIFICATIONS
•
Heater and blower standard.
•
Pendant mount standard, 1½ inch NPT quick
connect coupling.
connect coupling.
•
Thermostatically controlled 24VAC heater.
•
Durable engineered plastic top, UL94-5VA UV protected.
•
Clear or tinted dome (1 F stop light reduction).
•
Enhanced optical dome.
•
IP67, designed to meet NEMA 4X for water ingress.
Pressurized Dome Enclosures
UNI-OPL7C2 & UNI-OPL7T2
Security Camera Enclosures
The UNI-OPL7C2 and UNI-OPL7T2 are 7-inch pressurized
housings offering versatility and camera protection in
a compact size. Pressurization eliminates the effects of
moisture, dirt, and pollution on valuable camera
equipment. A heater and blower are standard. 24VAC
input. A tinted dome is available as part number
UNI-OPL7T2. Designed for the Sony SNC-RS44/46,
SNC-RH124, SNC-RZ25, SNC-RX, SNC-EP/ER 520/550/580,
and SNC-ZR550/ZP550 series cameras.
housings offering versatility and camera protection in
a compact size. Pressurization eliminates the effects of
moisture, dirt, and pollution on valuable camera
equipment. A heater and blower are standard. 24VAC
input. A tinted dome is available as part number
UNI-OPL7T2. Designed for the Sony SNC-RS44/46,
SNC-RH124, SNC-RZ25, SNC-RX, SNC-EP/ER 520/550/580,
and SNC-ZR550/ZP550 series cameras.