Руководство По Установке для KitchenAid 30-Inch 4-Burner Dual Fuel Downdraft Slide-In Range

Скачать
Страница из 52
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
Tape measure
 
Phillips 
screwdriver
 
 Flat-blade 
screwdriver
 
 ¹⁄
8
" (3 mm) flat-
blade screwdriver
 Level
 Drill
  Adjustable wrench
Slip joint pliers
  Pipe wrench
  
15
16
" (2.4 cm) 
combination 
wrench
 
 ¹⁄
8
" (3.2 mm) drill 
bit (for wood 
floors)
  Marker or pencil
 
5¹⁄
2
" hole saw (round ducting)
 
Saw for 3¹⁄
4
" x 10" rectangle 
vent
  #2 square bit and driver
 Flashlight
  Masking tape
   Pipe-joint compound resistant 
to natural and LP gases
  
3
16
" (4.8 mm) carbide-tipped 
masonry drill bit (for concrete/
ceramic floors)
 
 Noncorrosive  leak-detection 
solution
   Sheet metal aluminum tape
For LP/Natural Gas Conversions
   ½" (13 mm) combination 
wrench
  ¼" (6 mm) nut driver
  
9
32
" (7 mm) nut driver
Parts Supplied
Check that all parts are included.
LP/Natural gas conversion kit (dual fuel models only)
Blower mounting/venting template
Grease filter (packaged in place)
Oven racks (3)
Blower motor kit (under unit)
Blower cover kit (packed in cavity)
10-32 hex nuts (attached to terminal block) (3)
Direct wire lugs (3)
#12 x 1
5
8
" (4.1 cm) screws (for mounting anti-tip bracket) (2)
Anti-tip bracket (inside oven cavity)
 
 Anti-tip bracket must be securely mounted to the back wall 
or floor. Thickness of flooring may require longer screws 
to anchor bracket to subfloor. Longer screws are available 
from your local hardware store.
Parts Needed
 
Use an approved vent cap for proper performance. If an 
alternate wall or roof cap is used, be certain the cap size  
is not reduced and that it has a backdraft damper.
 
After determining your vent installation, one of the following 
is needed:
 
 5" (12.7 cm) Round surface wall cap damper – 
Order Part Number A405.
 
 6" (15.2 cm) Round surface wall cap damper – 
Order Part Number A406.
  
NOTE: If using 6" (15.2 cm) round venting, you will need  
a 5" (12.7 cm) to 6" (15.2 cm) round vent transition.
 
 3¼" x 10" (8.3 x 25.4 cm) Surface wall cap damper –  
Order Part Number A403.
To order, see the “Assistance or Service” section of the Use and 
Care Guide:
– Metal ducting
– Vent clamp
– Aluminum foil tape
Check local codes and consult gas supplier. Check existing 
gas supply and electrical supply. See the appropriate “Electrical 
Requirements” and “Gas Supply Requirements” sections.
It is recommended that all electrical connections be made by  
a licensed, qualified electrical installer.
Optional Parts
To purchase these or any other accessories, please reference 
the “Accessories” section of the Use and Care Guide for 
contact information.
 
Side Trim Kits:
 5
8
" (1.7 cm) Black – Order Part Number W10675026
 
 5
8
" (1.7 cm) Stainless Steel –  Order Part Number 
W10675028
 1¹⁄
8
" (2.9 cm) Black – Order Part Number W10731886
 
 1¹⁄
8
" (2.9 cm) Stainless Steel –  Order Part Number 
W10731887
 
Backsplash Kits:
 
High 6" (15.2 cm) Black – Order Part Number W10655449
 
 High 6" (15.2 cm) Stainless Steel – Order Part Number 
W10655450