Инструкция для Canon VB-H610VE
Installing the Camera
The following explains the procedures to install the camera on a ceiling using the recessed mounting kit.
Before installing the camera, set the IP address and other network information on the camera using the tool on the
Setup CD-ROM. For further details, see “Operation Guide”.
If using an memory card, insert the memory card into the camera before attaching the dome case (see “Installation
Guide” > “Using an Memory Card” included with the camera).
Before installing the camera, set the IP address and other network information on the camera using the tool on the
Setup CD-ROM. For further details, see “Operation Guide”.
If using an memory card, insert the memory card into the camera before attaching the dome case (see “Installation
Guide” > “Using an Memory Card” included with the camera).
1
Determine an installation position for the camera and drill holes in the ceiling
Use the included template to determine the positions of the holes (three) for mounting the backside ceiling bracket
and the ceiling bracket holes according to the camera orientation. Next, drill holes ( 205 mm ( 8.07 in.)) in the
ceiling.
Use the template with the printed side facing you.
and the ceiling bracket holes according to the camera orientation. Next, drill holes ( 205 mm ( 8.07 in.)) in the
ceiling.
Use the template with the printed side facing you.
2
Assemble the ceiling brackets
Interlock the embossed locating pins of ceiling bracket 1 with the locating bores in ceiling bracket 2. Fix the
brackets with the 3 included assemble screws (M3).
The position of the locating bores on ceiling bracket 2 differs according to the camera. Refer to the diagram to
interlock the brackets correctly.
brackets with the 3 included assemble screws (M3).
The position of the locating bores on ceiling bracket 2 differs according to the camera. Refer to the diagram to
interlock the brackets correctly.
Important
Check that the interlocked brackets are fixed by the embossed locating pins.
3
Loosen the three lock screws on the dome case and remove the dome case
Special tamper-resistant screws are used for the dome case lock screws. Use the dome case lock screw wrench
included with the camera.
included with the camera.
4
Remove the tape and the inner cover
Remove the 4 pieces of tape that prevent lens rotation during shipping, and push the inner cover in the direction of
the arrows to remove it. Then remove the 2 pieces of tape attached to the base of the lens.
the arrows to remove it. Then remove the 2 pieces of tape attached to the base of the lens.
Important
Do not move the lens unit by hand. This can damage the lens unit.
5
Open the wiring hole according to the installation method
Use a box cutter to cut a cross shape into the wiring hole cover in order to guide cables through.
Do not remove the wiring hole cover.
Do not remove the wiring hole cover.
Use a coin to unscrew the wiring hole cover from the side through which cables will be guided. Screw the wiring
hole cover into the other wiring hole. You can fit a composite pipe (NPT 3/4 inch threaded hole) to the wiring hole.
hole cover into the other wiring hole. You can fit a composite pipe (NPT 3/4 inch threaded hole) to the wiring hole.
6
Mount the camera to the ceiling bracket assembly
Fix with three included camera fixing screws (M4).
The screw holes differ according to the camera. Refer to the diagram to fix the camera using the correct screw
holes.
The screw holes differ according to the camera. Refer to the diagram to fix the camera using the correct screw
holes.
7
Attach the backside ceiling brackets inside the ceiling
From the inside of the ceiling, insert the protrusions on the backside ceiling brackets through the mounting holes
drilled in step 1.
drilled in step 1.
8
Temporarily tighten screws to the backside ceiling brackets
Temporarily tighten the three included ceiling bracket screws (M4) through the ceiling.
9
Secure the safety wire
Securely attach the safety wire to an anchor or structure. After securing one end of the safety wire to the ceiling,
secure the other end to the camera using the screw that is fastened to the camera.
secure the other end to the camera using the screw that is fastened to the camera.
10
Guide the LAN cable through the wiring hole
When using an external power supply, guide the power interface cable through the wiring hole. Guide the I/O
interface cable and the audio interface cable (included with the camera) through the wiring hole if necessary.
interface cable and the audio interface cable (included with the camera) through the wiring hole if necessary.
Important
When using the AC Adapter (sold separately), cut the cable tie and remove the ferrite core. Be
sure not to damage the power cable when cutting the cable tie.
sure not to damage the power cable when cutting the cable tie.
Cable tie
11
Fix the camera-mounted ceiling bracket assembly to the ceiling
Position the ceiling bracket assembly onto the screws temporarily tightened in step 8, turn clockwise and
completely fasten the screws.
completely fasten the screws.
12
Wire the cables
Wire the cables referring to the “Installation Guide” > “Cable Wiring Method” included with the camera.
13
Attach the inner cover
Attach the inner cover to its original position.
14
Attach the dome case
Firmly fix the dome case at three points to the camera using the dome case screws.
15
Attach the recessed mounting cover
Align the (O) mark on the recessed mounting cover with the (I) mark on the ceiling bracket, and turn clockwise
until the (I) mark on the recessed mounting cover aligns with the (I) mark on the ceiling bracket. Fix the recessed
mounting cover.
until the (I) mark on the recessed mounting cover aligns with the (I) mark on the ceiling bracket. Fix the recessed
mounting cover.
16
Set the camera angle
When installation is complete, use the Camera Angle Setting Tool to adjust the pan, tilt, rotation, zoom (and focus)
(see “Operation Guide” > “Camera Angle Setting Tool”).
(see “Operation Guide” > “Camera Angle Setting Tool”).
2
Embossed
locating pins
Included
screw
M3 x 3
3
Dome case
Inner cover
4
Lock screw
holes
5
When guiding cables through the side
When guiding cables through the ceiling
wiring hole
wiring hole
6
Included
screw
M4 x 3
7
9
8
Included
screw
M4 x 3
11
13
14
Dome case
15
Safety wire
Secure to an anchor
or structure
LAN cable
Backside ceiling brackets
Ceiling board
Main unit
Dome
Ceiling bracket assembly
* Illustrations without icons are examples of VB-H610D/VB-M600D.