Примечания к выпуску для Cisco Cisco 3365 Mobility Services Engine
14
Release Notes for Cisco Mobility Services Engine, Release 8.0.110.0
OL-32458-01
Upgrading the MSE
•
To use download software available locally or over the network, select the Browse a new software
image to transfer into the Server radio button, and click Choose File. Locate the file, and click
Open.
image to transfer into the Server radio button, and click Choose File. Locate the file, and click
Open.
Step 7
Click Download to send the software to the /opt/installers directory on the Mobility Services Engine.
Step 8
When using Prime Infrastructure to transfer the image to MSE, the file will be decompressed, and the
“.gz” will be removed from the filename. Verify that the MSE image file
(CISCO-MSE-L-K9-8-0-110-0-64bit.bin.tar) is in the Mobility Services Engines
/opt/installers directory.
“.gz” will be removed from the filename. Verify that the MSE image file
(CISCO-MSE-L-K9-8-0-110-0-64bit.bin.tar) is in the Mobility Services Engines
/opt/installers directory.
Note
When copying the image file directly to the MSE, without using Prime Infrastructure, the filename on
MSE will remain unchanged and it will be CISCO-MSE-L-K9-8-0-110-0-64bit.bin.tar.gz.
MSE will remain unchanged and it will be CISCO-MSE-L-K9-8-0-110-0-64bit.bin.tar.gz.
Step 9
Go to /opt/installers and create a directory to extract the installer files using the command:
mkdir 8.0.110.0
mkdir 8.0.110.0
Step 10
Move to the new directory using the command: cd 8.0.110.0
Step 11
To unpack the installation files, run the following command:
tar xvf ./CISCO-MSE-L-K9-8-0-110-0-64bit.bin.tar
This unpack yields the following three files. These three files must be in the same directory when
running the installer. The installation process uses the MSE_PUB.pem and signhash.bin to validate the
integrity of the MSE image.
running the installer. The installation process uses the MSE_PUB.pem and signhash.bin to validate the
integrity of the MSE image.
•
Cisco-MSE-L-K9-8-0-110-0-64bit.bin
•
MSE_PUB.pem
•
signhash.bin
Note
If the MSE image file was transfered directly to the MSE and not downloaded using PI, then the
following command should be used to decompress and unpack the installer files:
tar zxvf ../CISCO-MSE-L-K9-8-0-110-0.bin.tar.gz
following command should be used to decompress and unpack the installer files:
tar zxvf ../CISCO-MSE-L-K9-8-0-110-0.bin.tar.gz
Step 12
Make sure that the CISCO-MSE-L-K9-8-0-110-0-64bit.bin file has execute permissions for
the root user. If not, enter the following command:
the root user. If not, enter the following command:
chmod +x CISCO-MSE-L-K9-8-0-110-0-64bit.bin
Step 13
Manually stop the MSE service using the following command:
/etc/init.d/msed stop
or service msed stop
Step 14
To install the new Mobility Services Engine image, enter the following command:
/opt/installers/8.0.110.0/CISCO-MSE-L-K9-8-0-110-0-64bit.bin
Note
The installation process takes a minimum of 30 minutes. The actual installation time depends on the
amount of data present in your system. After the installation, you need to reboot the system before
starting the MSE.
amount of data present in your system. After the installation, you need to reboot the system before
starting the MSE.
Step 15
Start the new Mobility Services Engine software by entering the following command. If you attempt to
start the MSE, it just returns an error saying that MSE needs to be rebooted.
start the MSE, it just returns an error saying that MSE needs to be rebooted.
/etc/init.d/msed start