Руководство По Установке для Cisco Cisco TelePresence MX700
Back to task overview
Configuring IP
(when not set by a provisioning system)
Your video conference system supports both iP version 4
(iPv4) and iP version 6 (iPv6). in both cases, the iP param-
eters can be assigned automatically by the network, or you
can set everything manually.
if you want to set the parameters manually please contact
your network administrator to obtain the required parameters.
if your system is provisioned automatically, these iP settings
may be overridden by the provisioning system.
if an iPv4 or iPv6 address is already assigned to the system, you
will find it on the System information page. Go to
Diagnostics
tab and choose
System Information
.
NoTe:
You must restart the system after changing the iP
settings for the changes to take effect.
To set or change the IPv4 settings
Go to the
Configuration
tab and choose
System Configuration
.
1. Choose IP version
Click the
Network
settings in the left sidebar. under
General
Settings
choose
IPv4 in the
IPStack
drop down list.
2. Choose automatic or manual IP assignment
Choose
DHCP in the
Assignment
drop down list if you
want automatic iP assignment; or
Static if you want to set
the iP addresses manually.
3. If IP Assignment is Static: Set the IP addresses
a. Scroll down the page to the
IPv4
section and enter
the
Address
,
Gateway
and
SubnetMask
in the corre-
sponding input fields.
b. Scroll up to the
DNS
section and enter the dNS server
address in the
Server 1 Address
input field.
To set or change the IPv6 settings
Go to the
Configuration
tab and choose
System Configuration
.
1. Choose IP version
Click the
Network
settings in the left sidebar. under
General
Settings
choose
IPv6 in the
IPStack
drop down list.
2. Choose automatic or manual IP assignment
Scroll down the page to the
IPv6
section and choose
DHCPv6, Autoconf or Static in the
Assignment
drop down
list according to your network requirements.*
3. If IP Assignment is Static: Set the IP addresses
enter the system iP address in the
Address
input field and
the gateway address in the
Gateway
input field.
4. If IP Assignment is Static or Autoconf:
DHCPoptions
Choose
on or off in the
DHCPOptions
drop down list
according to your network requirements.**
5. If DHCPoptions is off: Configure DNS and NTP
a. Scroll up to the
DNS
section and enter the dNS server
address in the
Server 1 Address
input field.
b. open the
NetworkServices
settings from the left
sidebar and scroll down to the
NTP
section. enter
the NtP server address in the
Address
input field.
Set
Mode
to
Auto
.
If you are changing a value setting,
you have to always click
save
to confirm the change.
* iP Assignment:
dHCPv6: All iPv6 addresses, including options, are obtained automatically
from a dHCPv6 server.
Autoconf: the system and gateway iP addresses will be assigned
automatically. the options, e.g. NtP and dNS server addresses, must be
set/assigned according to the dHCP options setting. **
Static: the system and gateway iP addresses must be configured manually.
the options, e.g. NtP and dNS server addresses, must be set/assigned
according to the dHCP options setting. **
** dHCP options:
on: the iP parameters, like the dNS and NtP server addresses, will be
obtained automatically from a dHCPv6 server.
off: the iP parameters, like the dNS and NtP server addresses, must be
set manually.
Cisco TelePresence Video Systems
D14639.09 Video Systems Getting Started Guide TC6.1, April 2013.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
25
Getting Started Guide
Contents
Introduction
User interfaces
Configuration
Appendices
Contacts
Confirguration