Release Note для Cisco Cisco TelePresence MX700
Known limitations
Cisco TelePresence System C/EX/SX/MX Series Software Release Notes
Page 111 of 194
N/A
Ver. Any
If you run cascaded cameras and the chained
cameras are running an old camera code, we
have seen that zoom only works when trying to
control the chained camera. The solution is to
connect the cascaded camera as the first
camera in the chain so that the camera is
detected and upgraded by the codec, or use the
Ethernet upgrade method.
cameras are running an old camera code, we
have seen that zoom only works when trying to
control the chained camera. The solution is to
connect the cascaded camera as the first
camera in the chain so that the camera is
detected and upgraded by the codec, or use the
Ethernet upgrade method.
N/A
Ver. Any
HD-SDI may not work with cables shorter than
3 meters. This is due to a jitter issue.
3 meters. This is due to a jitter issue.
N/A
Ver.Any
If you turn off H.323 as the protocol but leave
default protocol as H.323 you will be unable to
make outgoing calls unless you edit the URI to
include 'sip:' in front of the number or change
the default call protocol to SIP.
default protocol as H.323 you will be unable to
make outgoing calls unless you edit the URI to
include 'sip:' in front of the number or change
the default call protocol to SIP.
CSCts05791
Any
The following HDMI output formats:
“1920*1200p60, 800*600 and 1920*1080p60
(CVR960H) reduced blanking”, will run in DVI
compatibility mode and hence audio cannot be
transmitted over HDMI when using this
resolution.
“1920*1200p60, 800*600 and 1920*1080p60
(CVR960H) reduced blanking”, will run in DVI
compatibility mode and hence audio cannot be
transmitted over HDMI when using this
resolution.
CSCtr32423
Ver. TC3.x and above
If you dial a TANDBERG 150 with SW version
L5.1.1 or older with encryption setting set to
‘on’, you may not get audio in any direction.
L5.1.1 or older with encryption setting set to
‘on’, you may not get audio in any direction.
N/A
TC3.0.0 and above
The Cisco TelePresence System codec
C40/C60 (rev. 1), will not provide proper
analogue VGA output for any resolution of 1080
lines or more.
C40/C60 (rev. 1), will not provide proper
analogue VGA output for any resolution of 1080
lines or more.
N/A
Any
The Cisco TelePresence System codec C40
will reduce its capability set when using internal
MultiSite. When this is done, the mainstream is
at maximum able to transmit w576p until all
calls are disconnected.
will reduce its capability set when using internal
MultiSite. When this is done, the mainstream is
at maximum able to transmit w576p until all
calls are disconnected.
N/A
Any
The Cisco TelePresence System codec C60
will reduce its capability set when using internal
MultiSite. When this is done, the dual stream is
at maximum able to transmit WXGA until all
calls are disconnected.
will reduce its capability set when using internal
MultiSite. When this is done, the dual stream is
at maximum able to transmit WXGA until all
calls are disconnected.
N/A
Any
The Cisco TelePresence System EX60/90 does
not support usage of the remote control. The
Cisco TelePresence Touch 8 Screen must be
used to control these devices.
not support usage of the remote control. The
Cisco TelePresence Touch 8 Screen must be
used to control these devices.
CSCtr32298
TC4
To use SIP verified, a CA list must be uploaded
to the /user folder using SCP (root user must be
enabled). The CA list must be named
‘sipcalist.pem’ and be in DER format.
to the /user folder using SCP (root user must be
enabled). The CA list must be named
‘sipcalist.pem’ and be in DER format.