для Cisco Cisco Packet Data Gateway (PDG)
Accounting Policy Configuration Mode Commands
cc ▀
Command Line Interface Reference, StarOS Release 17 ▄
237
buckets num
Default: 4
Specifies the number of container changes in the S-GW CDR due to QoS changes or tariff times. If an
accounting policy is not configured, this value is 4. GTPP accounting will use the default value if the
configured value is beyond 4.
In 12.1 and earlier releases,
Specifies the number of container changes in the S-GW CDR due to QoS changes or tariff times. If an
accounting policy is not configured, this value is 4. GTPP accounting will use the default value if the
configured value is beyond 4.
In 12.1 and earlier releases,
num
must be an integer value from 1 through 4.
In release 12.2,
num
must be an integer value from 1 through 10.
In 12.3 and later releases,
num
must be an integer value from 1 through 20.
Important:
Please note that the maximum value for the CC profile buckets is extended to support up to 10 for
Diameter Rf accounting only. However, in the case of GTPP accounting, this CLI command allows configuring only up
to 4 buckets.
to 4 buckets.
interval seconds
Default: disabled
Specifies a time interval for closing the charging record if the minimum volume thresholds are satisfied.
Specifies a time interval for closing the charging record if the minimum volume thresholds are satisfied.
seconds
must be an integer value from 60 through 40000000.
sdf-interval seconds
Default: disabled
Specifies a time interval for closing the charging record for a specific flow if the minimum volume thresholds
are satisfied.
Specifies a time interval for closing the charging record for a specific flow if the minimum volume thresholds
are satisfied.
seconds
must be an integer value from 60 through 40000000.
sdf-volume { downlink octets { uplink octets } | total octets
| uplink octets
{
downlink octets
} }
Specifies octet volume thresholds for the generation of interim CDRs for a specific flow.
downlink
octets
: Sets the threshold limit for the number of downlink octets that must be reached before
the charging record for a specific flow is closed.
octets
must be an integer value from 100000 through
4000000000.
total
octets
: Sets the threshold limit for the total number of octets that must be reached before the
charging record for a specific flow is closed.
octets
must be an integer value from 100000 through
4000000000.
uplink
octets
: Sets the threshold limit for the number of uplink octets that must be reached before the
charging record for a specific flow is closed.
octets
must be an integer value from 100000 through
4000000000.
serving-nodes num
Default: 4
Specifies the number of serving node changes (inter-serving node switchovers) after which the interim CDR
is generated. In P-GW and S-GW, a partial record needs to be generated whenever there is a serving node
address list overflow. Serving node is added to the CDR list during handover scenarios.
Specifies the number of serving node changes (inter-serving node switchovers) after which the interim CDR
is generated. In P-GW and S-GW, a partial record needs to be generated whenever there is a serving node
address list overflow. Serving node is added to the CDR list during handover scenarios.
num
must be an
integer value from 1 through 4. If an accounting policy is not configured, this value is 4.
tariff time1 min hrs [ time2 min hrs...time4
min hrs
]
Specifies time-of-day values used to determine when a container is closed in the charging records.
time1
min hrs
: Specifies the first time-of-day value used to close the current container in the charging
record.
min
must be an integer value from 0 through 59.
hrs
must be an integer value from 0 through 23.