Краткое Руководство По Установке для Brother LX-3125/3125E
Toll Free Phone 877-276-8437
Relative Chart of Sewing Fabrics,
Needles and Thread Combinations
Sewing Fabrics
Needle Sizes
Thread Sizes
Very Thin
Fine tricot, Fine lace, Thin linen,
Silk, Organza, Chiffon
#65/9
Cotton: 80
Synthetic/Polyester Long Fiber
Fine Mercerized Cotton
Lightweight
Voile, Taffeta, Synthetics, Silk,
Batiste
#75/11
Cotton: 60-80
Silk: “A”
Synthetic/Polyester Long Fiber
Mercerized 50
Medium Weight
Cotton, Gingham, Poplin,
Percale, Pique, Satin, Velvet,
Lightweight wool, Fine
corduroy, Suitings, Linen,
Muslin
#90/14
(Supplied with
your machine)
your machine)
Cotton: 50-60
Silk: “A”
Synthetic/Polyester Long Fiber
Mercerized 50-60
Heavyweight
Denim, Gabardine, Tweed,
Corduroy, Canvas, Duck
#100/16
Cotton: 40-50
Mercerized Heavy Duty
Polyester Long Fiber
Knits
Single knit, Double knit, Jersey,
Tricot
#90/14
(Ball point)
Cotton Wrapped Polyester
Polyester Long Fiber
Uses common replacement accessories:
Bobbin: Class
Bobbin: Class
15
Needle:
Standard sewing machine needles
Light Bulb:
Small screw base sewing machine bulb
Utiliza accesorios comunes de remplazo:
Carretel: Clase
Carretel: Clase
15
Agujas:
Agujas estándares para máquina de coser.
Bombilla:
Para máquina de coser con base roscada pequeña
Pull up on the thread spool pin to lengthen the height. Place the thread spool on the pin
and pass the thread around the bobbin winder pre-tension disc.
and pass the thread around the bobbin winder pre-tension disc.
Pass the thread through the hole
on the bobbin from inside. Use
upper hole, not both. Place on
bobbin shaft and slide to the right.
on the bobbin from inside. Use
upper hole, not both. Place on
bobbin shaft and slide to the right.
While holding the end of the thread,
press the foot controller to begin
winding the thread. Cut the thread
from the top and proceed winding.
press the foot controller to begin
winding the thread. Cut the thread
from the top and proceed winding.
When the bobbin starts to spin
slowly and becomes full, release
the foot controller. Cut the thread,
slide the bobbin winding shaft to
the left and remove the bobbin.
slowly and becomes full, release
the foot controller. Cut the thread,
slide the bobbin winding shaft to
the left and remove the bobbin.
Raise the needle to its highest position and
remove the bobbin case by pulling the latch.
remove the bobbin case by pulling the latch.
Hold the bobbin case as shown. Insert the
bobbin with the thread coming from the bottom
toward the top and the thread tail hanging out of
the bobbin case.
bobbin with the thread coming from the bottom
toward the top and the thread tail hanging out of
the bobbin case.
Pull the trailing thread through the
slot, down and to the left, until it
enters the delivery eye under the
tension spring. CAUTION: Make
sure you set the bobbin so the thread
unrolls in the right direction. If the
thread unrolls in the wrong direction,
it may cause the thread tension to be
incorrect or break the needle.
slot, down and to the left, until it
enters the delivery eye under the
tension spring. CAUTION: Make
sure you set the bobbin so the thread
unrolls in the right direction. If the
thread unrolls in the wrong direction,
it may cause the thread tension to be
incorrect or break the needle.
Holding the bobbin case by the latch,
align your fi nger with the top opening
of the shuttle race, insert the case
into the shuttle race and release the
latch.
align your fi nger with the top opening
of the shuttle race, insert the case
into the shuttle race and release the
latch.
Winding the Bobbin
Inserting the Bobbin
1
2
1
2
3
4
1
2
3
4
Not winding the bobbin properly may
cause the thread tension to loosen, and
may break the needle.
cause the thread tension to loosen, and
may break the needle.
CAUTION
1 Wound evenly
2 Wound poorly
2 Wound poorly
Threading the Needle
Raise the thread take-up lever to
its highest position by turning the
handwheel.
its highest position by turning the
handwheel.
Place the thread spool on the
spool pin.
(Don’t forget to pull up the pin)
spool pin.
(Don’t forget to pull up the pin)
Pass the thread through the thread guide and down the
right channel on the front of the machine.
right channel on the front of the machine.
Pass the thread into the thread tension discs or behind the
thread tension dial from the right to the left.
thread tension dial from the right to the left.
Grasp the thread on both sides of the tension disc and pull to
ensure it is in place.
ensure it is in place.
Guide the thread up the left channel, clear to the back of the opening around
the take-up lever and back down the left side of the channel to thread the
take-up lever.
the take-up lever and back down the left side of the channel to thread the
take-up lever.
Thread the needle from front to back and pull
out about 5 cm (2 inches) of thread.
out about 5 cm (2 inches) of thread.
2
3
4
5
6
7
8
Cleaning the Bobbin Case
Remove the power plug from the outlet.
Raise the needle to its highest position,
pull the latch and remove the bobbin
case.
pull the latch and remove the bobbin
case.
Slide the latch levers out from the
retaining ring.
retaining ring.
Remove the hook by grasping the center
post and pulling out. Note its position
related to the driver.
post and pulling out. Note its position
related to the driver.
Remove the retaining ring.
Remove any accumulated lint and
thread with a brush.
thread with a brush.
Grasp the center post of the hook, match
the hook position opposite the driver and
insert.
the hook position opposite the driver and
insert.
Insert the retaining ring with the notch
up.
up.
Push the latch levers into their locked
position. Replace the bobbin case.
position. Replace the bobbin case.
1
5
4
3
2
9
8
7
6
Raise the presser foot lifter.
1
XE5240-201.indd 2
XE5240-201.indd 2
2009/11/05 18:35:28
2009/11/05 18:35:28