Руководство По Работе для Brother PR1050X

297

The needle threader 
cannot be used.

The needle is not at the correct 
position.

Touch the key to move the desired 
needle bar to be threaded into 
embroidering position.

p.63

Recommended needles are not used on 
this machine.

Replace and use recommended needle.

p.33, 86

The needle is not installed correctly.

Correctly install the needle.

p.33, 86

The hook on the automatic needle-
threading mechanism is bent.

Consult your nearest authorized 
Brother dealer.

The thread tension is 
incorrect.

The upper thread is not threaded 
correctly.

Check the thread path, and then thread 
the upper thread again.

p.57

The bobbin thread is not correctly 
threaded.

Correctly thread the bobbin thread.

p.36

The lower thread tension is incorrect.

Adjust the tension of the bobbin thread.

p.124

Lint or dust has accumulated in the 
thread tension disc.

Remove the tension dials, and then 
remove any lint or dust accumulated 
between the felt washers.

p.287

The upper thread 
comes out of the 
needle when 
embroidering begins.

If a short length of thread remains after 
the thread is trimmed, the needle may 
become unthreaded when 
embroidering begins again.

Set the remaining length of thread to 
“Long Tail” on the second page of the 
settings screen.

p.228

The upper thread does 
not reach the bobbin 
thread when 
embroidering begins.

There is no more thread in the bobbin, 
the thread does not feed from the 
bobbin, or the thread that is fed from 
the bobbin is too short.

Correctly thread the lower thread.

p.36

Although the thread is 
not broken, a broken 
thread error occurs 
and the machine stops.

If the thread breakage sensor in the 
thread tension disc of the thread 
tension knobs cannot detect that the 
thread is being fed, even if the machine 
is running, a broken thread error occurs 
and the machine is stopped. If the 
thread came out of the thread tension 
disc, even though the thread is not 
broken, the machine detects that the 
thread is not being fed and stops.

Clean the tension unit. Correctly pass 
the thread through the thread tension 
disc. If the broken thread error occurs 
after the machine is cleaned and 
rethreaded, the sensor may be 
damaged. Consult your nearest 
authorized Brother dealer.

p.59, 287

The thread is worn.

Lint or dust has accumulated in the 
thread tension disc.

Remove the tension dials, and then 
remove any lint or dust accumulated 
between the felt washers.

p.287

Jumpstitches are long.

Lint or dust has accumulated in the 
thread tension disc.

Remove the tension dials, and then 
remove any lint or dust accumulated 
between the felt washers.

p.287

There are needle cuts 
or holes in the 
garment.

The needle is dull.

Replace the needle. Dull needles have 
a difficult time passing through the 
garment, causing fabrics to tear.

p.33, 86

The fabric is too delicate.

The simple penetration of the needle 
could damage delicate fabrics. Use 
stabilizer on top of fabric.

p.254

There is puckering in 
the fabric.

The thread tension is too tight.

Adjust the tension according to the type 
of fabric and thread being used. 
Polyester thread will stretch during 
sewing especially if the tensions are set 
too high. After the stitching is complete, 
the thread returns to its original 
strength, causing puckers in the fabric.

p.125

The framing tension of the fabric is 
incorrect.

Tightly frame non-stretchable, woven 
fabrics. Loose framing will cause the 
fabric to bunch up under the stitching.
Tautly frame soft knits using a stable 
backing. Overstretching the garment 
will cause it to look puckered when the 
frame is removed.

p.253

The column stitches are too long.

Re-digitize the design with fill stitching 
or with multiple rows of column 
stitching.