Справочник Пользователя для Samsung RF26NBSH
Setting up your French Door Refrigerator
Installing the water filter
1. Remove the water filter cover(
1
)
2. Remove the fixed cap by turning it counter
clockwise. Keep the cap in a safe place for later use
if you don’t use a filter.
if you don’t use a filter.
3. Remove the water filter from the box and put a
replacement indicator sticker on the filter as shown.
Place a sticker on the filter that dates six months
in the future. For example, if you install the water
filter in March, put the “SEP” sticker on the filter to
remind you to replace in September. That way you’ll
know when it is time to replace the filter. Normally, a
filter life is about 6 months.
Place a sticker on the filter that dates six months
in the future. For example, if you install the water
filter in March, put the “SEP” sticker on the filter to
remind you to replace in September. That way you’ll
know when it is time to replace the filter. Normally, a
filter life is about 6 months.
4. Remove the filter cap and insert the filter into the
filter housing.
5. Slowly turn the water filter 90º clockwise to align
with the printing mark on the cover, locking the filter
in position. Make sure to align the water filter label
mark with center of cover filter printing as illustrated.
Remember, do not over-tighten.
in position. Make sure to align the water filter label
mark with center of cover filter printing as illustrated.
Remember, do not over-tighten.
2
3
1
4
5
Sticker
(month indicator)
Separation
of red cap.
Cover filter.
Turn until the
labels are
aligned.
You should remove the right side upper glass shelf
before installing water filters.
before installing water filters.
Removing any residual matter inside the water supply line after installing the
water filter.
1. Turn ON the main water supply.
2. Run water through the dispenser until the water runs clear 3L. This will clean
2. Run water through the dispenser until the water runs clear 3L. This will clean
the water supply system and remove air from the lines.
3. Additional flushing may be required in some households. But , the filter will
have an operational life proportional to the quality of the water supplied). The
time is not guaranteed.
4. Open the Refrigerator door and make sure there are no water leaks coming
from the water filter.
Reverse Osmosis Water Supply
IMPORTANT : The pressure of the water supply coming out of a reverse osmosis system going to
the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).
If a reverse osmosis water filtration system is connected to your cold water supply, the water
If a reverse osmosis water filtration system is connected to your cold water supply, the water
pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa.)
If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):
• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the
If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):
• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the
filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill after heavy usage.
• If your refrigerator has a water filter, it may further reduce the water pressure when used in
• If your refrigerator has a water filter, it may further reduce the water pressure when used in
conjunction with a reverse osmosis system. Remove the water filter.
If you have questions about your water pressure, call a licensed, qualified plumber.
Be sure to flush the dispenser thoroughly, otherwise water may drip from
the dispenser. This means that there is still air in the line.
the dispenser. This means that there is still air in the line.
16_
Setting Up
DA99-01623F-03.indd 16
2010.10.15 8:35:16 AM