Инструкции По Обслуживанию для HP pavilion ze4115

Reference Information
Modem Reference Information

142

Reference Guide

+MS=

a

,

b

,

c

,

d

,

e

,

f

Select modulation (

b

, 

c

, 

d

, 

e

, and 

f

 are optional).

a

 is the carrier (allowable rates in parentheses): B103 (300), B212 (1200 Rx/75 Tx or 75 Rx/1200 Tx),

V21 (300), V22 (1200), V22B (1200/2400), V23C (1200), V32 (4800/9600), V32B (4800–14400), V34
(2400–33600), K56 (32000–56000), V90 (28000–56000), V92 (downstream: 28000–56000; upstream:
24000–48000).

b

 is automode: 0=disabled, 1=enabled (default).

c

 is minimum transmit (Tx) rate (bps).

d

 is maximum transmit rate (bps).

e

 is minimum receive (Rx) rate.

f

 is maximum receive rate (bps).

+WS=

n

Set PDC mode: 1=disable (default), 20=enable.

%C

n

Set data compression: 0=disable, 1=enable V.42 bis and MNP 5, 2=enable V.42 bis and MNP 5,
3=enable V.42 bis and MNP 5 (default).

+EB=

a

,

b

,

c

Select break handling (

b

 and 

c

 are optional):

a

=0 — break is ignored.

b

=0 — transmitted V.42 L-SIGNAL will not indicate break signal length.

c

=0 — break is not delivered to DTE.

+EFCS=0

Select 16-bit FCS specified in V.42.

+ER: 

a

Select error control protocol: NONE=error control not in use, LAPM=V.42 LAPM protocol, ALT=MNP.

+ER=

n

Error control reporting: 0=disable, 1=enable.

+ES=

a

,

b

,

c

Select error control and synchronous mode (

b

 and 

c

 are optional).

a

 is requested mode when modem is originator: 0=initiate call with direct mode, 1=initiate call with

normal mode, 2=initiate V.42 without detection phase, 3=initiate V.42 with detection phase (default),
4=initiate MNP, 6=initiate V.80 synchronous access mode when connection is completed.

b

 specifies fallback mode when modem is originator: 0=LAPM, MNP, or normal mode error control

optional (default); 1=LAPM, MNP, or direct mode error control optional; 2=LAPM or MNP error control
required; 3=LAPM error control required; 4=MNP error control required.

c

 specifies fallback mode when modem is answerer or specifies V.80 synchronous access mode:

1=error control disabled, use normal mode; 2=LAPM, MNP, or normal mode error control optional
(default); 3=LAPM, MNP, or direct mode error control optional; 4=LAPM or MNP error control
required; 5=LAPM error control required; 6=MNP error control required; 8=initiate V.80 synchronous
access mode when connection complete.

+ESR=0

Disable selective repeat option in V.42.

+ETBM=

a

,

b

,

c

Handle data remaining in modem buffers on call termination (

b

 and 

c

 are optional):

a

=0 — disconnect occurs immediately and buffered transmit data is discarded.

b

=0 — disconnect occurs immediately and buffered receive data is discarded.

c

=0 — modem does not attempt to deliver buffered data and discards data.

+FAE=

n

Data/fax auto answer: 0=disable (default), 1=enable.

+FAR=

n

0=disable adaptive reception (default), 1=enable.

+FCL=

n

Set loss-of-carrier delay in units of 100 ms (

n

=0 to 255).

+FCLASS=

n

Set active service class: 0=data mode (default), 1=Fax Class 1, 1.0=Fax Class 1.0 mode, 8=voice
mode.

+FIT=

n

,

a

Set DTE inactivity timeout 

n

 seconds after which modem goes on-hook (

a

=0) or DCE goes on hook

(

a

=1).

+FLO=

a

Set flow control type: 0=XON/XOFF and RTS/CTS flow control turned off; 1=XON/XOFF flow control
in either direction; 2=RTS for flow control of modem by DTE, and CTS for flow control of DTE by
modem.