Справочник Пользователя для Sony 500WSPL
88
Chapter 4
Viewfinder Screen Indications and Menus
Chapter 4 Viewfinder Screen Indications and Menus
Viewfinder Advanced Menu
Advanced menu page 3
a) For DSR-500WSPL: EBU75
Item
Settings
GAIN
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
LOW
Sets the L position.
Sets the L position.
–3 dB, 0 dB (normal
value), 3 dB, 6 dB, 9 dB,
12 dB, 18 dB, 18 dB + DPR,
24 dB
value), 3 dB, 6 dB, 9 dB,
12 dB, 18 dB, 18 dB + DPR,
24 dB
MID
Sets the M position.
Sets the M position.
0 dB, 3 dB, 6 dB, 9 dB
(normal value), 12 dB,
18 dB, 18 dB + DPR, 24 dB,
24 dB + DPR
(normal value), 12 dB,
18 dB, 18 dB + DPR, 24 dB,
24 dB + DPR
HIGH
Sets the H position.
Sets the H position.
3 dB, 6 dB, 9 dB, 12 dB,
18 dB (normal value),
18 dB + DPR, 24 dB, 24 dB
+ DPR, HYPER GAIN
18 dB (normal value),
18 dB + DPR, 24 dB, 24 dB
+ DPR, HYPER GAIN
DL
Sets DynaLatitude function
ON/OFF. This setting is
valid only when the
OUTPUT/DL/DCC+ switch
has been set to CAM/DL.
Sets DynaLatitude function
ON/OFF. This setting is
valid only when the
OUTPUT/DL/DCC+ switch
has been set to CAM/DL.
ON (normal value), OFF
When set to ON, the amount
of DynaLatitude effects is
set in the basic menu page 2
(see page 81). For details on
the DynaLatitude function,
see page 50.
When set to ON, the amount
of DynaLatitude effects is
set in the basic menu page 2
(see page 81). For details on
the DynaLatitude function,
see page 50.
Advanced menu page 2
Item
AWB MEM
Selects whether or not
to make the FILTER
control settings (1 to 4)
correspond to
separate white
balance adjustment
values stored in
memory.
Selects whether or not
to make the FILTER
control settings (1 to 4)
correspond to
separate white
balance adjustment
values stored in
memory.
2 (normal value): No
correspondence with FILTER
control settings. Only two
adjustment values (A and B) are
stored in memory.
2
correspondence with FILTER
control settings. Only two
adjustment values (A and B) are
stored in memory.
2
×
4FL: Correspondence with
FILTER control settings. Each of
the four control settings can be
used to set A and B adjustment
values, for a total of eight settings.
the four control settings can be
used to set A and B adjustment
values, for a total of eight settings.
TONE
Selects whether or not
to output a 1-kHz
audio signal with the
color bars when the
OUTPUT/DL/DCC+
has been set to
BARS.
Selects whether or not
to output a 1-kHz
audio signal with the
color bars when the
OUTPUT/DL/DCC+
has been set to
BARS.
ON (normal value): Outputs
audio signal.
OFF: Does not output audio
signal.
audio signal.
OFF: Does not output audio
signal.
BARS
Selects normal width
or narrower width for
color bars.
Selects normal width
or narrower width for
color bars.
SMPTE (normal value for DSR-
500WSL): Normal width
EBU75 (normal value for DSR-
500WSPL): EBU 75%
EBU100 (for DSR-500WSPL):
EBU 100%
SPLIT (for DSR-500WSPL): Not
for normal operation
SNG: Narrower than normal (used
for satellite communications, etc.)
500WSL): Normal width
EBU75 (normal value for DSR-
500WSPL): EBU 75%
EBU100 (for DSR-500WSPL):
EBU 100%
SPLIT (for DSR-500WSPL): Not
for normal operation
SNG: Narrower than normal (used
for satellite communications, etc.)
REMOTE1
Sets a function for
switch 1 of the RM-
LG1 connected to the
REMOTE connector 1.
Sets a function for
switch 1 of the RM-
LG1 connected to the
REMOTE connector 1.
REC (normal value): Specifies
recording start/stop.
MARK: Specifies a Mark IN/OUT
point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
recording start/stop.
MARK: Specifies a Mark IN/OUT
point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
REMOTE2
Sets a function for
switch 2 of the RM-
LG1 connected to the
REMOTE connector 1.
Sets a function for
switch 2 of the RM-
LG1 connected to the
REMOTE connector 1.
9600, 38400 (normal value)
REC: Specifies recording start/stop.
MARK (normal value): Specifies
a Mark IN/OUT point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
MARK (normal value): Specifies
a Mark IN/OUT point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
Settings
BAUD RATE
Sets a baud rate for a
computer connected
to the REMOTE
connector 2 (to be
supported in the future
version).
Sets a baud rate for a
computer connected
to the REMOTE
connector 2 (to be
supported in the future
version).
P A G E 2 ( N E X T m
$ P R E V m4)
G A I N
m L O W : O d B
M I D : 9 d B
H I G H : 1 8 d B
H Y P E R : 3 6 d B
D L : O N
H I G H : 1 8 d B
H Y P E R : 3 6 d B
D L : O N
E X I T M E N U ( Y E S
m P U S H )
P A G E 3 ( N E X T
m
$ P R E V m4)
m A W B M E M : 2
T O N E : O N
B A R S : S M P T E
R E M O T E 1 : R E C
R E M O T E 2 : M A R K
B A U D R A T E : 3 8 4 0 0
B A R S : S M P T E
R E M O T E 1 : R E C
R E M O T E 2 : M A R K
B A U D R A T E : 3 8 4 0 0
E X I T M E N U ( Y E S
m P U S H )
a)
HYPER
Sets the HYPER position.
Sets the HYPER position.
36 dB (normal value),
42 dB
42 dB