Справочник Пользователя для Sony DSR-1600A
39
Menu Contents
C
h
ap
te
te
r 4
M
e
e
nu
S
e
S
e
tti
n
gs
SEARCH ENABLE [>Search ENA]: Select how the unit enters
the search mode.
*
DIAL DIRECT [>> DIAL]: Press the SEARCH button or,
except during editing, turn the search dial.
VIA SEARCH KEY [>> via KEY]: Press the SEARCH button.
MAX SRCH SPEED [>Max
SRCH]: Specify the
maximum tape speed in
search mode (shuttle) and
F.FWD (fast forward)/REW
(rewind) mode.
maximum tape speed in
search mode (shuttle) and
F.FWD (fast forward)/REW
(rewind) mode.
SHUTTLE [>>SHUTTLE]:
Specify the maximum
tape speed in search
mode (shuttle).
tape speed in search
mode (shuttle).
X60 [>>> X60]: Maximum 60 times normal speed
*
*
X32 [>>> X32]: Maximum 32 times normal speed
X16 [>>> X16]: Maximum 16 times normal speed
F.FWD/REW [>>F.FWD/
REW]: Specify the
maximum tape speed
in F.FWD/REW mode.
maximum tape speed
in F.FWD/REW mode.
MAX [>>> MAX]: No maximum tape speed is specified.
*
*
X85 [>>> X85]: Maximum 85 times normal speed
X60 [>>> X60]: Maximum 60 times normal speed
X32 [>>> X32]: Maximum 32 times normal speed
X32 [>>> X32]: Maximum 32 times normal speed
Note
When this item is set to MAX, the playback video signal is
muted.
muted.
JOG RESPONSE [>JOG dial]: Select the tape speed
characteristics for the search dial rotation rate in jog mode.
*
TYPE1 (–1 to +1) [>> type 1]: Tape speed varies linearly
over the range
−1 to +1.
TYPE2 (–3 to +3) [>> type 2]: Tape speed varies stepwise as
shown in the figure below over the range
−3 to +3.
(Characterized by a zone around
−1 and +1 where the
tape speed is independent of the rotation rate)
TYPE3 (–3 to +3) [>> type 3]: Tape speed varies linearly over
the range
−3 to +3, as shown in the figure below.
PREROLL TIME [> Preroll]: Set the preroll time.
0 SEC [>> 0 sec] to 15 SEC [>> 15 sec]: The preroll time
can be set in one-second increments to between 0 and 15
seconds.
seconds.
A preroll time of at least 5 seconds is recommended when
using this unit for editing. When an editing control unit such as
the PVE-500 has been connected, this setting is disabled and
the setting on the editing control unit is in effect. Operations
such as the preroll time setting and the time data switching
operation are also performed on the editing control unit.
Factory default setting: 5 SEC [>> 5 sec]
using this unit for editing. When an editing control unit such as
the PVE-500 has been connected, this setting is disabled and
the setting on the editing control unit is in effect. Operations
such as the preroll time setting and the time data switching
operation are also performed on the editing control unit.
Factory default setting: 5 SEC [>> 5 sec]
AFTER CUE-UP [> After CUE]: Select the operating mode
following cue-up.
*
STOP [>> STOP]: Stop mode
STILL [>> STILL]: Output still pictures in search mode.
PLAY START [> PLAY start]: Set the timing for switching from
stop mode to playback mode.
In an editing system including an editing control unit such as
the PVE-500, you can adjust this setting so that the delay
before switching to playback mode is the same on all the decks
of the editing system. It is then no longer necessary to
synchronize the decks for editing, and the preroll time can be
shortened.
the PVE-500, you can adjust this setting so that the delay
before switching to playback mode is the same on all the decks
of the editing system. It is then no longer necessary to
synchronize the decks for editing, and the preroll time can be
shortened.
16 FRAME DELAY [>> 16 delay] to 4 FRAME DELAY [>> 4
delay]: The larger the numerical value, the longer the
delay. By adjusting this setting, it is possible to reduce the
phase synchronization time and preroll time during
editing.
delay. By adjusting this setting, it is possible to reduce the
phase synchronization time and preroll time during
editing.
Factory default setting: 5 FRAME DELAY [>> 5 delay] (for
DSR-1600A) or 4 FRAME DELAY [>> 4 delay] (for DSR-
1600AP)
1600AP)
AUTO REW [>Auto REW]: Select whether to rewind the tape
automatically when recording or playback reaches the end
of a tape.
of a tape.
DISABLE [>> DISABLE]: Do not rewind the tape
automatically.
*
ENABLE [>> ENABLE]: Rewind the tape automatically.
OPERATIONAL FUNCTION [Operational]: Operation
settings
settings
Description of settings
+3
+1
-1
-3
FWD
FWD
RVS
RVS
+3
-3
FWD
FWD
RVS
RVS
TYPE3
TYPE2
Speed
Speed
Rotation rate
Rotation rate