Справочник Пользователя для Sony ht ddw1600
74
GB
There is no sound from one of the front
speakers.
speakers.
• Connect a pair of headphones to the
PHONES jack to verify that sound is
output from the headphones. If only one
channel is output from the headphones, the
component may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both
channels are output from the headphones,
the front speaker may not be connected to
the receiver correctly. Check the
connection of the front speaker which is
not outputting any sound.
output from the headphones. If only one
channel is output from the headphones, the
component may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both
channels are output from the headphones,
the front speaker may not be connected to
the receiver correctly. Check the
connection of the front speaker which is
not outputting any sound.
• Make sure you have connected to both the
L and R jacks of an analog component, and
not only to either the L or R jack. Use an
audio cord (not supplied).
not only to either the L or R jack. Use an
audio cord (not supplied).
There is no sound from analog 2
channel sources.
channel sources.
• Check that the INPUT MODE is not set to
“COAX IN” or “OPT IN” for the selected
input (page 62).
input (page 62).
There is no sound from digital sources
(from COAXIAL or OPTICAL input
jack).
(from COAXIAL or OPTICAL input
jack).
• Check that the INPUT MODE is not set to
The source sound input to the HDMI
jack on the receiver is not output from
the TV speaker.
jack on the receiver is not output from
the TV speaker.
• Check the HDMI connection.
• You cannot listen to the Super Audio CD
• You cannot listen to the Super Audio CD
by connecting HDMI.
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with each component.
Refer to the operating instructions
supplied with each component.
There is no sound from the speakers of
the receiver when you connect the
receiver and the playback component
via a HDMI connection.
the receiver when you connect the
receiver and the playback component
via a HDMI connection.
• Make sure that you have connected the
digital audio jacks on the playback
component to the receiver. Then, turn off
or mute the TV’s volume.
component to the receiver. Then, turn off
or mute the TV’s volume.
The left and right sounds are
unbalanced or reversed.
unbalanced or reversed.
• Check that the speakers and components
are connected correctly and securely.
• Adjust the balance parameters using the
LEVEL menu.
There is severe hum or noise.
• Check that the speakers and components
are connected securely.
• Check that the connecting cords are away
from a transformer or motor, and at least
3 m away from a TV set or fluorescent
light.
light.
• Move your audio components away from
the TV.
• The plugs and jacks are dirty. Wipe them
with a cloth slightly moistened with
alcohol.
alcohol.
There is no sound, or only a very low-
level sound is heard from the center/
surround/surround back speakers.
level sound is heard from the center/
surround/surround back speakers.
• Select a CINEMA STUDIO EX mode
• Adjust the speaker level (page 36).
There is no sound from the surround
back speaker.
back speaker.
• Some discs have no Dolby Digital
Surround EX flag even though the
packages have Dolby Digital Surround EX
logos. In this case, select “SB ON” (page
46).
packages have Dolby Digital Surround EX
logos. In this case, select “SB ON” (page
46).
There is no sound from the sub woofer.
• Check that the sub woofer is connected
correctly and securely.
• Make sure you have turned on your sub
woofer.