Справочник Пользователя для Sony HDW-D1800
55
6-2 Shot Mark Operations
Cha
p
te
r 6
S
hot
Mar
k
F
u
nc
ti
ti
on
6-2 Shot Mark Operations
This section describes the operations concerning reading
and writing shot marks. Note that the following operations
cannot be carried out by remote control.
Shot mark operations are carried out from function menu
page P104: SHOT MRK. Select F3 (SHOT MRK) in
function menu page P05: MISC-2 to open function menu
page P104: SHOT MRK.
and writing shot marks. Note that the following operations
cannot be carried out by remote control.
Shot mark operations are carried out from function menu
page P104: SHOT MRK. Select F3 (SHOT MRK) in
function menu page P05: MISC-2 to open function menu
page P104: SHOT MRK.
6-2-1 Reading Shot Marks
To read in shot marks
With a cassette tape loaded and F7 (LIST) selected, press
the F FWD or REW button.
While the shot marks are being read in, the F FWD or
REW button flashes.
The unit searches to the end of the tape, then rewinds
automatically.
the F FWD or REW button.
While the shot marks are being read in, the F FWD or
REW button flashes.
The unit searches to the end of the tape, then rewinds
automatically.
For the procedure for listing the read shot marks, see
page 56.
page 56.
It is possible to read in a maximum of 200 shot marks.
When 200 shot marks have been read in, the ancillary
message display on the control panel shows “SHOT LIST
FULL”, and the reading stops.
To cancel the message, press one of the tape transport
buttons.
When 200 shot marks have been read in, the ancillary
message display on the control panel shows “SHOT LIST
FULL”, and the reading stops.
To cancel the message, press one of the tape transport
buttons.
To stop reading
Press the STOP button.
Press the STOP button.
To read shot marks from more than one
cassette
cassette
After changing the cassettes, carry out the reading
operation again.
Data written in the new cassette will be added as long as
the total does not exceed 200 shot marks. For example, if
operation again.
Data written in the new cassette will be added as long as
the total does not exceed 200 shot marks. For example, if
190 shot marks have already been read in, only 10 shot
marks will be read from the new tape.
In the shot mark list (see page 56) the data from different
cassettes is separated by a separator.
marks will be read from the new tape.
In the shot mark list (see page 56) the data from different
cassettes is separated by a separator.
6-2-2 Writing Shot Marks
To write recording start marks during
recording
recording
In setup menu item 631 “REC START MARK MODE”,
select whether or not to write a recording start mark for
each of the three recording modes (CRASH REC,
ASSEMBLE, INSERT).
When you set a particular mode to “ON”, a recording start
mark is written on the tape each time you start recording in
that mode.
select whether or not to write a recording start mark for
each of the three recording modes (CRASH REC,
ASSEMBLE, INSERT).
When you set a particular mode to “ON”, a recording start
mark is written on the tape each time you start recording in
that mode.
When using the insert edit mode, select F2 (INS TC) in
function menu page P07: E.PRESET, turning it on.
function menu page P07: E.PRESET, turning it on.
To write shot mark 1, shot mark 2 or post
marks
marks
To select the type of shot mark to be written
In setup menu item 636 “MARK SELECT IN REC/
ASSEMBLE”, select SHOT1, SHOT2 or POST mark.
In setup menu item 636 “MARK SELECT IN REC/
ASSEMBLE”, select SHOT1, SHOT2 or POST mark.
If any of the mode settings in setup menu item 631 “REC
START MARK MODE” is set to “ON” (to write a
recording start mark), then the user bits are overwritten
with the shot mark data for 20 frames from the start of
recording in crash recording mode, assemble edit mode or
insert edit mode.
START MARK MODE” is set to “ON” (to write a
recording start mark), then the user bits are overwritten
with the shot mark data for 20 frames from the start of
recording in crash recording mode, assemble edit mode or
insert edit mode.
To write in crash recording or assemble editing
1
Holding down the SHIFT/ENTRY button, select F2
(REC/ERS) in function menu page P104: SHOT MRK
to set “REC”.
(REC/ERS) in function menu page P104: SHOT MRK
to set “REC”.
A mark can be written only when F2 is set to “REC”.
2
At the position you want to write the mark, hold down
the SHIFT/ENTRY button and select F3 (REC).
the SHIFT/ENTRY button and select F3 (REC).
A mark of the type selected in the setup menu item 636
is written.
is written.
Note
SHOT MRK
R E C / E R S
R E C
R E C
R E C
SHOT MRK
M A R K
L I S T
E X I T
Note
Note
Note