Справочник Пользователя для Sony power had ex dvcam dsr-400l

22

Location and Function of Parts

  Ch

ap
te

r 1  Ov

e

rv

ie

w

b Trigger mode
PARA: Operates both internal and external VTRs.
INT: Operates the internal VTR only.
EXT: Operates the external VTR only.

c Extender
“EX” is displayed when a lens extender is used.

d Color temperature
Indicates the currently selected color temperature.

e DC IN / battery voltage / remaining capacity
Indicates the battery voltage or the remaining capacity of 
an attached internal battery pack, an AC adaptor, or an 
external battery (a battery connected to the DC IN 
connector).
When the power is supplied from an external battery, “DC 
IN” appears here.
When the DISP BATT REMAIN item is set to INT on the 
VF DISP 2 page of the OPERATION menu, the battery 
voltage is not indicated. 
However, when the Anton Bauer intelligent battery system 
or the BP-GL65/GL95 battery pack is used, the remaining 
battery capacity is automatically detected and indicated in 
steps of 10%.
• Until the remaining battery capacity is reduced to 40%, 

the indications MAX, 90%, 80%...40% are displayed for 
three seconds in the viewfinder each time the remaining 
battery capacity reduces by 10%.

• When the remaining battery capacity is less than 40%, 

the indication is displayed all the time.

• When the remaining battery capacity is less than 10%

*

, 

the indication flashes. When the remaining battery 
capacity is reduced further, the “LOW” flashes.

* This value can be set to either 10% or 20% on the FUNCTION 2 page of 

the OPERATION menu.

f * (Asterisk indicator)
Flashes when the color bars are displayed and is recorded 
together with the color bars.

g 16:9 mode recording indicator (DSR-450WS/

Indicates recording in the 16:9 mode. This indicator is 
recorded together with the color bars.

h Setting change and adjustment progress message 

For details, see “Display modes and setting change 
confirmation/adjustment progress messages” on page 99.

i EXT/IV indicator (DSR-450WS/450WSP only)
Displayed when a CBK-SC01 Composite Input Board is 
installed for input of external composite signals.

j Recording format
Indicates the current recording format.

k Iris setting/auto iris override
Indicates the F value (iris setting) of the lens.
Also, the auto iris override is displayed using two squares 
which appear in the upper and lower parts respectively.

l Remaining tape capacity
Indicates the remaining tape recording time (in minutes) of 
the VTR.

m Audio level
Indicates the level of audio channel 1 and channel 2. The 
peak indication of the VTR level meter is related as 
follows to the audio level when an 1kHz sine wave is input.

n Operation/error message display area
For details, see “Operation/error messages” on page 127.

o Shutter speed
Indicates the shutter speed or the shutter mode. However, 
if the SHUTTER switch (page 10) is set to OFF, nothing is 
displayed.
1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000: Shutter speed 

(in seconds) in standard mode (scan mode: I)

1/40, 1/60, 1/120, 1/125, 1/250, 1/500, 1/1000, 1/2000: 

Shutter speed (in seconds) in standard mode (scan 
mode: PsF)

ECS: In ECS (Extended Clear Scan) mode
EVS: In EVS (Super Enhanced Vertical Definition 

System) mode

1F to 8F, 16F (DSR-450WS/450WSP only): Number of 

frames in the slow speed shutter mode

p Gain
Indicates the gain of the video amplifier, as set by the 
GAIN switch.

F - 30

Full to 30 minutes

30 - 25

30 to 25 minutes

25 - 20

25 to 20 minutes

20 - 15

20 to 15 minutes

15 - 10

15 to 10 minutes

10 - 5

10 to 5 minutes

5 - 0

5 to 0 minutes

No display

0 minute

Audio channel 1 level 
indicator

Audio channel 2 level 
indicator

VTR level meter 
indicator