Справочник Пользователя для Sony power had ex dvcam dsr-400l
54
Recording
C
h
h
a
p
ter
4
R
e
e
co
rd
rd
in
g
an
d
d
Pl
a
y
b
a
c
k
4
Before the shutter setting indication in step 3
disappears, push the SHUTTER switch down to
SELECT again. Repeat this until the desired mode or
speed appears.
disappears, push the SHUTTER switch down to
SELECT again. Repeat this until the desired mode or
speed appears.
The settings of mode and speed preselected on the
SHT ENABLE page of the OPERATION menu
displayed. Note that all modes and all standard-mode
speeds listed in the table on page 52 are preselected
using the SHT ENABLE page of the OPERATION
menu. By factory default, all available shutter modes
and shutter speeds are displayed in the sequence
shown in the following figure. (You can use the SHT
ENABLE page of the OPERATION menu to make a
setting so that only the desired (or most frequently
used) modes and speeds are displayed.)
SHT ENABLE page of the OPERATION menu
displayed. Note that all modes and all standard-mode
speeds listed in the table on page 52 are preselected
using the SHT ENABLE page of the OPERATION
menu. By factory default, all available shutter modes
and shutter speeds are displayed in the sequence
shown in the following figure. (You can use the SHT
ENABLE page of the OPERATION menu to make a
setting so that only the desired (or most frequently
used) modes and speeds are displayed.)
To set the shutter speed in ECS mode
1
Follow steps in “To set the shutter mode and standard
mode shutter speed” on page 53 to set the shutter
speed mode to ECS.
mode shutter speed” on page 53 to set the shutter
speed mode to ECS.
2
Turn the MENU knob until the desired frequency
appears.
appears.
The selectable frequency range varies depending on
the scan mode. See the table on “About the shutter
modes” on page 52.
the scan mode. See the table on “About the shutter
modes” on page 52.
When the RM-B150 Remote Control Unit is
connected
You can set the shutter speed of ECS with the rotary
encoder of the RM-B150.
connected
You can set the shutter speed of ECS with the rotary
encoder of the RM-B150.
To set the shutter speed in SLS mode
1
Follow steps in “To set the shutter mode and standard
mode shutter speed” on page 53 to set the shutter
speed mode to SLS.
mode shutter speed” on page 53 to set the shutter
speed mode to SLS.
2
Turn the MENU knob until the desired number of
frames appears.
frames appears.
The number of frames can be set to values in the range
1 to 8, and 16 (1 frame nearly equals to
1 to 8, and 16 (1 frame nearly equals to
1
/
30
second).
To change the range of shutter mode and speed
settings
You can reduce the time required to select the shutter mode
and speed by narrowing the choice of settings in advance.
This can be done by using the SHT ENABLE page of the
OPERATION menu.
settings
You can reduce the time required to select the shutter mode
and speed by narrowing the choice of settings in advance.
This can be done by using the SHT ENABLE page of the
OPERATION menu.
The settings selected on the SHT ENABLE page of the
OPERATION menu become invalid when the RM-B150
Remote Control Unit is connected to the camcorder.
OPERATION menu become invalid when the RM-B150
Remote Control Unit is connected to the camcorder.
1
Display the SHT ENABLE page of the OPERATION
menu.
menu.
For details on menu operations, see “Basic menu
operations” on page 93.
operations” on page 93.
2
Press the MENU knob. Then turn the MENU knob to
move
move
b to the shutter mode or shutter speed you want,
then press the MENU knob again.
b changes to z, and z changes to ?.
Example of standard mode (when the scan mode is set to I)
SLS mode
ECS mode
1 2
ECS:60.00Hz
Note
1 2
SLS: 1/30 : 1FRAME
? 16 SHT ENABLE TOP
SHUTTER SLS : ON
SHUTTER ECS : ON
SHUTTER 1/100 : ON
SHUTTER 1/125 : ON
SHUTTER 1/250 : ON
SHUTTER 1/500 : ON
SHUTTER 1/1000 : ON
SHUTTER 1/2000 : ON