Справочник Пользователя для Sony rdr-gx380
78
Timer recording is not complete or did not start
from the beginning.
from the beginning.
, There was a power failure before or during
recording. Reset the clock (page 67).
, Another timer setting overlapped the timer
setting (page 40).
, Disc space was not sufficient.
Contents previously recorded were erased.
, Data that is not playable on this recorder but was
recorded on a DVD with a PC will be erased
from the disc when the disc is inserted.
from the disc when the disc is inserted.
The clock has stopped.
, Set the clock again (page 67).
, The clock stopped due to a power failure. Reset
, The clock stopped due to a power failure. Reset
the clock (page 67).
The “
” indicator is flashing.
, The disc does not have enough space.
, Insert a recordable disc into the recorder.
, Insert a recordable disc into the recorder.
The recording mode indication is incorrect.
, When the recording or dubbing is less than three
minutes, the recording mode indication may be
displayed incorrectly. The actual recording itself
is correctly made in the selected recording mode.
displayed incorrectly. The actual recording itself
is correctly made in the selected recording mode.
The remote does not function.
, The batteries are weak.
, The remote is too far from the recorder.
, There is an obstacle in the path of the remote
, The remote is too far from the recorder.
, There is an obstacle in the path of the remote
control and the recorder.
, The remote’s manufacturer code returned to the
default setting when you replaced the batteries.
Reset the code (page 19).
Reset the code (page 19).
, Turn on the recorder.
, The remote is not pointed at the remote sensor on
, The remote is not pointed at the remote sensor on
the recorder.
, Different command modes are set for the
recorder and remote. Set the same command
mode (page 19). The default command mode
setting for this recorder and the supplied remote
is “3 (Default setting).” You can check the
current command mode in the front panel display
(page 19).
mode (page 19). The default command mode
setting for this recorder and the supplied remote
is “3 (Default setting).” You can check the
current command mode in the front panel display
(page 19).
Other Sony equipment responds to the remote.
, The same command mode is set for both the
equipment and recorder. Set a different
command mode for the recorder (page 19).
command mode for the recorder (page 19).
The recorder does not detect USB memory
connected to the recorder.
connected to the recorder.
, Make sure that the USB memory is securely
connected to the recorder (page 26).
, Check that the USB memory is not damaged.
The recorder does not operate properly.
, Restart the recorder. Press down
"/1
on the
recorder for more than five seconds until the
recorder turns off. If a disc is still in the recorder,
press Z (open/close) and remove the disc.
recorder turns off. If a disc is still in the recorder,
press Z (open/close) and remove the disc.
, When static electricity, etc., causes the recorder
to operate abnormally, turn off the recorder and
wait until the clock appears in the front panel
display. Then, unplug the recorder and after
leaving it off for a while, plug it in again.
wait until the clock appears in the front panel
display. Then, unplug the recorder and after
leaving it off for a while, plug it in again.
The disc tray does not open after you press Z
(open/close).
(open/close).
, It may take a few seconds for the disc tray to
open after you have recorded or edited a DVD.
This is because the recorder is adding disc data to
the disc.
This is because the recorder is adding disc data to
the disc.
Mechanical sound is heard when the recorder
is off.
is off.
, While the recorder is adjusting the clock for the
Auto Clock Set function or operational noises
(such as the internal fan) may be heard, even
when the power is off. This is not a malfunction.
(such as the internal fan) may be heard, even
when the power is off. This is not a malfunction.
Display
Remote control
Others