Справочник Пользователя для Sony SDM-S74E
9
GB
Setup 5: Turn on the monitor and
computer
1
Press the MAIN POWER switch located on the right
side of the monitor in the direction of the [, if it is not
already pressed. Make sure the 1 (power) indicator
is lit in red.
side of the monitor in the direction of the [, if it is not
already pressed. Make sure the 1 (power) indicator
is lit in red.
Note
The monitor is factory shipped with the MAIN POWER switch set to on
([).
The monitor is factory shipped with the MAIN POWER switch set to on
([).
2
Press the 1 (power) switch located on the front
right of the monitor.
The 1 (power) indicator lights up in green.
right of the monitor.
The 1 (power) indicator lights up in green.
3
Turn on the computer.
4
Press the
m/M buttons to select the desired input
signal (SDM-S74E only).
The selected input’s picture appears on the screen.
For more information, see “Selecting the input signal (INPUT
button) (SDM-S74E only)” on page 10.
The selected input’s picture appears on the screen.
For more information, see “Selecting the input signal (INPUT
button) (SDM-S74E only)” on page 10.
The installation of your monitor is complete. If necessary, use the
monitor’s controls to adjust the picture (page 11).
monitor’s controls to adjust the picture (page 11).
If no picture appears on your screen
• Check that the power cord and the video signal cables are
properly connected.
• If “NO INPUT SIGNAL” appears on the screen:
– The computer is in the power saving mode. Try pressing any
– The computer is in the power saving mode. Try pressing any
key on the keyboard or moving the mouse.
– Check that the input signal setting is correct by pressing the
m/M buttons (SDM-S74E only) (page 10).
• If “CABLE DISCONNECTED” appears on the screen:
– Check that the video signal cables are properly connected.
– Check that the input signal setting is correct by pressing the
– Check that the video signal cables are properly connected.
– Check that the input signal setting is correct by pressing the
m/M buttons (SDM-S74E only) (page 10).
• If “OUT OF RANGE” appears on the screen:
Reconnect the old monitor. Then adjust the computer’s
graphics board within the following ranges.
graphics board within the following ranges.
SDM-S73E
SDM-S74E
For more information about the on-screen messages, see “Trouble
symptoms and remedies” on page 19.
symptoms and remedies” on page 19.
No need for specific drivers
The monitor complies with the “DDC” Plug & Play standard and
automatically detects all the monitor’s information. No specific driver
needs to be installed to the computer.
The first time you turn on your computer after connecting the monitor, the
setup Wizard may appear on the screen. If this is the case, follow the on-
screen instructions. The Plug & Play monitor is automatically selected so
that you can use this monitor.
The monitor complies with the “DDC” Plug & Play standard and
automatically detects all the monitor’s information. No specific driver
needs to be installed to the computer.
The first time you turn on your computer after connecting the monitor, the
setup Wizard may appear on the screen. If this is the case, follow the on-
screen instructions. The Plug & Play monitor is automatically selected so
that you can use this monitor.
The vertical frequency turns to 60 Hz.
Since flickers are unobtrusive on the monitor, you can use it as is. You do
not need to set the vertical frequency to any particular high value.
Since flickers are unobtrusive on the monitor, you can use it as is. You do
not need to set the vertical frequency to any particular high value.
MAIN POWER
lights in red
lights in green
INPUT
Analog RGB
Horizontal
frequency
frequency
28–80 kHz
Vertical
frequency
frequency
48–75 Hz
Resolution
1280
× 1024 or less
Analog RGB
Digital RGB
Horizontal
frequency
frequency
28–80 kHz
28–64 kHz
Vertical
frequency
frequency
48–75 Hz
60 Hz
Resolution
1280
× 1024 or less