Справочник Пользователя для Panasonic cq-c5100n

7

Note: 
¡

The volume level can be set independently for each
source. (For radio, one volume setting for AM
(LW/MW), one volume setting for all FMs)

ON : Press [MUTE].
OFF : Press [MUTE] again.
You can select mute or attenuation when [MUTE] is
pressed. (

a

Page 32)

You can utilize the rear speaker connected to the built-in
amplifier as Sub-Woofers that output only bass.
(Default: OFF)

Press and hold [MUTE] (SBC-SW) for more than 2 sec-
onds to switch SBC-SW on and off.

Note:
¡

When ON has been selected, the settings resulting from
the adjustments performed at the subwoofer level and
subwoofer low pass filter settings are reflected in the
output. (

a

Page 28)

¡

Depending on the speakers used and the type of music
played, it may not be possible to achieve a satisfactory
effect.

SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
type. For SQ7, you can also make fine adjustments for SQ
presetting, P2-P6, according to your taste. (

a

Page 26)

Press [SQ] to select a sound types as follows.

lights. (except SQ-FLAT)

(Default)

(Flat frequency response does not
emphasize.)

(Sharp and dynamic sound.
Powerful deep bass and turgescent
treble.)

(Prevention of excessive equalizing
and capability to cover wide variety
of music. Listener-friendly and crisp
sound.)

(Highlighted vocals that are apt to
be overwhelmed by instrumental
sound.)

(Sound with emphasis on sharpness
of high-hat and echo of saxophone.
Jazz-specific deep sound.)

(Reproduction of realism being in a
club.)

Press [DISP] to return to the regular mode.

Note:
¡

After pressing [SQ] on the main unit, you can also
select a sound type by pressing the preset buttons [1]-
[6].

¡

Setting of SQ, bass/treble and volume are influenced
one another. If the influence mentioned above causes
distortion to the audio signal, readjust bass/treble or
volume. (

a

Page 26)

Default: 18
Setting Range: 0 to 40

6

CQ-C5400N

CQ-C5400N

[SQ] (Sound Quality)

[DISP] (Display)

[MUTE] (Mute/attenuation)

indicator

[SOURCE] (PWR: Power)

Turn your car's ignition key to the ACC or ON position.

ON:

Press [SOURCE] (PWR).

OFF: Press and hold [SOURCE] (PWR) until you hear

a beep (about 1 second), then release it.

Note:
¡

When the ignition switch is turned ON, the panel is open
to secure their former positions.

¡

If the security function is set to ON, the security mes-
sage is shown with a warning alarm. (Default: S-LED
ON) (

a

Page 34 about Security Function setting)

ACC Selection
If your car has the ACC position on the ignition
switch, set the ACC selection to ON. (Default: ACC
OFF) 
(

a

Page 34)

is attached to the functional descriptions

under the ACC selection ON condition.

Demonstration Message
When the power is switched on for the first time, a
demonstration message appears on the display.
Press [DISP] to change to regular mode.

Scrolling....

Note:
¡

To display the message again, press and hold
[SOURCE] (PWR) for more than 4 seconds
when turning power on. 

Press [SOURCE] to change the source.

3CQ-C5400/C5300N

(

a

Page 10)

(

a

Page 19)

(When a MP3/WMA data disc is 

in the player. 

a

Page 20)

(When an optional CD changer is

connected. 

a

Page 24)

(

a

Installation instructions)

3CQ-C5100N

(

a

Page 10)

(

a

Page 19)

(When an optional CD changer is

connected. 

a

Page 24)

Remote control sensor (

a

Page 5)

Level Meter

Preset number

Spectrum analyzer